The Lee Universal Decapping die is made of steel and designed to allow shooters to decap cases without the need of lube or cleaning. Guaranteed by Lee as unbreakable. Easily removes crimped-in primers. Fits cases up to .550”, not recommended for use on .17-.20 calibers.
Mer...
Lee Universal Decapping-matrisen er laget av stål og designet for at skyttere kan bryte saker uten behov for smøremiddel eller rengjøring. Garantert av Lee som uknuselig. Fjerner enkelt innpressede primere enkelt. Passer tilfeller opp til .550 ”, anbefales ikke til bruk på 0,17 - 0,20 kaliber.
Mer...
Kundevurderinger for LEE PRECISION LEE DECAPPING DIE
Antall vurderinger: 6
Fra brownells.com: 6
Gjennomsnittsvurdering: 4,7
Works Well for most Calibers(17.02.2011)
The diameter of the decapping rod, which holds the decapping pin, is 0.202". Just small enough to enter a 20 caliber case mouth. Feed it slowly into a 20 caliber case though, because the end of the rod is not tapered enough to avoid possible contact with the case mouth. The diameter of the decapping pin is 0.062" and it is permanently attached to the rod. I'd like to see Lee also make a decapping rod with a 0.059" diameter pin for smaller flash holes like the 6mm BR. Also, if the pin breaks you have to throw away the rod too.
A must have(14.04.2012)
It makes so much sense to remove the primer before tumbling so the tumbling media can clean the primer pocket (if you use ground walnut). The previous reviewer ignored the fact that the die is not intended for calibers that are smaller than .22. Buy it and de-prime before you tumble. The price is great and replacement pins are cheap and easy to find.
Works Okay(04.05.2012)
Yep, it's a decapper. Not much more you can say about it...
Cheap & Works(29.06.2014)
I use this to de-prime all of my brass at a high volume and fast rate for: .223, .270. 300 Blackout, .30-06, etc. I have used this thing a lot and have not broken it yet; even on crimped military brass. I ultrasonic clean my brass after de-priming and have not touched a primer pocket cleaner in years.
Great work Lee!(08.01.2017)
This is the first die I reach for when its time to prep a new batch of rounds. Well machined and great design its incredibly simple. The decapping pin uses a collet, which by design will slip and not snap off if the primer does not wish to budge. Unlike most combination resizing/decapping dies that use a threaded pin that will snap when faced with a stubborn primer. Personally my case prep goes as fallows. De-cap, uniform the primer pocket, remove crimp, de-bur the flash hole. Then on the tumbler. I do it this way so my re-sizing dies never see a dirty case and therefore extending the life of my resizing dies. Great work Lee. Five stars!
Great Value(17.04.2018)
The Lee decapping die is well made, solid and has a nice polished metal finish. The purchase included the decapping pin. It has worked well de-priming crimped and uncrimped cases. It needs about 11 ft-lbs of torque to hold the decapping pin for crimped .223 Rem cases.
Produktnr.: 749001565 LEE PRECISION LEE DECAPPING DIE Produsentnr.: 90292734307902926 Lee Universal Decapping-matrisen er laget av stål og designet for at skyttere kan bryte saker uten behov for smøremiddel eller rengjøring. Garantert av Lee som uknuselig. Fjerner enkelt innpressede primere enkelt. Passer tilfeller opp til .550 ”, anbefales ikke til bruk på 0,17 - 0,20 kaliber.
Die Style:
Decapping Dies
Leveringsvekt: 0,181kgHøyde: 36mmBredde: 84mmLengde: 117mm
Elementdetaljer
Made in USA
Produktnr.: 100053256 LEE PRECISION LEE UNIVERSAL DECAP PIN Produsentnr.: 90783734307907839 Lee Universal Decapping-matrisen er laget av stål og designet for at skyttere kan bryte saker uten behov for smøremiddel eller rengjøring. Garantert av Lee som uknuselig. Fjerner enkelt innpressede primere enkelt. Passer tilfeller opp til .550 ”, anbefales ikke til bruk på 0,17 - 0,20 kaliber.
The Lee Universal Decapping die is made of steel and designed to allow shooters to decap cases without the need of lube or cleaning. Guaranteed by Lee as unbreakable. Easily removes crimped-in primers. Fits cases up to .550”, not recommended for use on .17-.20 calibers.
Mer...
Lee Universal Decapping-matrisen er laget av stål og designet for at skyttere kan bryte saker uten behov for smøremiddel eller rengjøring. Garantert av Lee som uknuselig. Fjerner enkelt innpressede primere enkelt. Passer tilfeller opp til .550 ”, anbefales ikke til bruk på 0,17 - 0,20 kaliber.
Mer...
Kundevurderinger for LEE PRECISION LEE DECAPPING DIE
Antall vurderinger: 6
Fra brownells.com: 6
Gjennomsnittsvurdering: 4,7
Works Well for most Calibers(17.02.2011)
The diameter of the decapping rod, which holds the decapping pin, is 0.202". Just small enough to enter a 20 caliber case mouth. Feed it slowly into a 20 caliber case though, because the end of the rod is not tapered enough to avoid possible contact with the case mouth. The diameter of the decapping pin is 0.062" and it is permanently attached to the rod. I'd like to see Lee also make a decapping rod with a 0.059" diameter pin for smaller flash holes like the 6mm BR. Also, if the pin breaks you have to throw away the rod too.
A must have(14.04.2012)
It makes so much sense to remove the primer before tumbling so the tumbling media can clean the primer pocket (if you use ground walnut). The previous reviewer ignored the fact that the die is not intended for calibers that are smaller than .22. Buy it and de-prime before you tumble. The price is great and replacement pins are cheap and easy to find.
Works Okay(04.05.2012)
Yep, it's a decapper. Not much more you can say about it...
Cheap & Works(29.06.2014)
I use this to de-prime all of my brass at a high volume and fast rate for: .223, .270. 300 Blackout, .30-06, etc. I have used this thing a lot and have not broken it yet; even on crimped military brass. I ultrasonic clean my brass after de-priming and have not touched a primer pocket cleaner in years.
Great work Lee!(08.01.2017)
This is the first die I reach for when its time to prep a new batch of rounds. Well machined and great design its incredibly simple. The decapping pin uses a collet, which by design will slip and not snap off if the primer does not wish to budge. Unlike most combination resizing/decapping dies that use a threaded pin that will snap when faced with a stubborn primer. Personally my case prep goes as fallows. De-cap, uniform the primer pocket, remove crimp, de-bur the flash hole. Then on the tumbler. I do it this way so my re-sizing dies never see a dirty case and therefore extending the life of my resizing dies. Great work Lee. Five stars!
Great Value(17.04.2018)
The Lee decapping die is well made, solid and has a nice polished metal finish. The purchase included the decapping pin. It has worked well de-priming crimped and uncrimped cases. It needs about 11 ft-lbs of torque to hold the decapping pin for crimped .223 Rem cases.