Attributes
- Modell:
70
- Våpentype:
Winchester
- Leveringsvekt: 0,068kg
- Frakthøyde: 25mm
- Fraktbredde: 48mm
- Fraktlengde: 152mm
- UPC: 050806008274
Produktnr.: 080097070
050806008274 Fjærbelastet verktøy gir konstant, rett bakovertrykk for å holde bolt lugs firkantet mot mottakeren mens du lapper med 600 til 800 grit, silisiumkarbid slipemiddel. Gir bedre resultater enn bare tommeltrykk. Utbyttbare gjengede sleeves passer til populære handlinger oppført nedenfor.Leveringstid ca. 14-21 dager.
BOLT LAPPING TOOLS, THREADED SLEEVE FOR WINCHESTER 70 ONLY fra BROWNELLS er designet for å gi konstant fjærtrykk for presis mating av låseklammer. Dette verktøyet er ideelt for å oppnå nøyaktige resultater når du lapping bolter.
Vår fjærbelastede verktøy gir konstant, rett bakovertrykk for å holde boltklammene kvadratiske mot mottakeren under lapping med 600 til 800 grit, silisiumkarbid-abrasiv. Dette gir bedre resultater enn bare tommelfingertrykk. De utskiftbare gjengede slevene passer til populære handlinger som er oppført nedenfor.
M14/M1A Set-sleiven inkluderer stor diameter plunger og spesialverktøy for lapping som kreves for disse modellene. Mauser Large sleeve passer til store ring Mauser handlinger, mens Mauser Small passer til små ring Mauser handlinger. Savage Small sleeve passer til Savage handlinger i alle kalibre unntatt Rem Ultra Mag (RUM), Rem SA Ultra Mag (RSUM), og Win Short Mag (WSM). Savage Large sleeve passer kun til Savage handlinger i RUM, RSUM, og WSM kalibre.
One Gun Set inneholder boltverktøy kropp, plunger, og riktig størrelse sleeve for modellen oppført. M14/M1A One Gun Set inneholder boltverktøy kropp, stor diameter plunger, riktig størrelse sleeve, og spesial sleeve, samt spesial bolt lapping verktøy unikt for M14/M1A/M1 Garand kun. Kitet inneholder alle verktøy som er nødvendige for å lappe alle modeller oppført i tabellen.
* Spesialpris, se nedenfor.
70
Winchester
Very nice fit of parts. 31.08.2015
I bought this one-gun kit after trying to use the plunger body from the M14/M1/M1A kit. It did not fit a sleeve I had bought for the Large Ring Mauser. After receiving this kit with it's plunger body I then began trying all the parts one at a time.
Both plunger bodies are 0.5620" and the sleeves are 0.5625 except the M14, it was 0.563. There were little burrs on the plunger body of the M14 kit that made me think it would not fit the different sleeves. All fit well after a little lapping.
I plan on using the bolt lug lapping tool for several rifles I am building. After using the tool I believe I can use it to square the bolt face on a Mauser Large Ring VZ-24. After reaming the sleeve from existing 9/16" to a 5/8" I will press fit a drill bushing that is 5/8 x 3/8 and use the Mason Reamer Burr which has a 3/8" shaft. The Burr has been ground to 0.3740 to 0.3745. It has a buttery slip fit in the Drill Bushing.
Mauser threads are at a 55 deg pitch and not easy to find. Brownells sells the sleeve with the right threads for the '98 and the face truing Burrs. All you need is the drill bushing, the undersized drill, and the reamer to make the altered sleeve to be able to Lapp the lugs with the original unaltered sleeve, and true the face of your bolt with your altered sleeve. After, of course, you check that the receivers threads are true to the action. This can be checked with a mandrel which Brownells has too. This can be done for any rifle that Brownells has a sleeve for. Happy Gunsmithing, JL.
Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.