Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge
080755000
With Special Tools For Colts & Mausers
The 30 tools and bits in the Assembly/Disassembly Kit are basically the same as those in the Basic Starter Kit except that four highly specialized tools have been substituted, making the Kit better equipped for somewhat more advanced professional work. Our decision on the tools is based on the fact that once a person gets started doing some gunsmithing, they quickly discover they are being brought a wider variety of guns than they had anticipated and that certain, seemingly "normal", assembly and disassembly steps can be difficult without the right tools. (This Kit is of paramount value to anyone doing gun rebluing and general repair service.) Colt handguns will be a part of your living. Whenever you disassemble either large or small frame revolvers, the ejector must be removed from the cylinder prior to polishing, bluing or servicing. The Colt Tool in the Kit makes this otherwise ticklish job quite simple. Plus, the tool makes it easier to remove or install tight 1911 Auto bushings. The Bolt Extractor Pliers can only be appreciated by one who has fought the removal and installation of a stiff extractor on an Enfield, Springfield, Mauser or similar bolt . . . Especially when your hands are "gunsmith greasy". Comes with illustrated instructions showing how to use when taking them off or putting them on. Magazine retaining caps on Ithaca 37's, Winchester Model 12's and similar, positively require the special Winchester Model 12 Wrench to remove. Will handle the toughest. Then there is the little 7/64" Speed-Head (Ball End) Socket Wrench. The first time you encounter a scope ring (like on newer Redfields) with Allen head screws on the bottom side of the rings, you will praise this tool for the lifesaver it is. Assembly/Disassembly Kit contains the following tools: No. 100 Parallel Pliers; 1" Nylon/Brass Hammer; No. 81 MAGNA-TIP® Screwdriver; Screwdriver Bits Nos. 1 - 2 - 6 - 00 - 10 - 20 and 30; Two sizes Instrument Screwdrivers; Main Spring Vise; MF134 India Stone; M-16 Brush; 1/8" x 6" Pin Punch; 5/32" x 6" Pin Punch; 1/16" Starter Punch; 3/32" Starter Punch; Brownells Replacement Pin-Punch Set; 2" Replacement Punch Assortment; Nylon/Brass Drift Pin Punch Set; Gunsmith Bench Knife; 8" No. 2 Cut Hand File; Sight Base File; Brownells Colt Pistol Wrench; Brownells Winchester Model 12 Wrench; Bolt Spring Extractor Pliers; Screw Check'r; 7/64" Speed-Hex (Ball-end) Wrench and Kit Box.
9599 9599 1 NOK
Produktnr.: 080755000
BROWNELLS ASSEMBLY/DISASSEMBLY KIT De 30 verktøyene og bitene i monterings-/demonteringssettet er i utgangspunktet de samme som i Basic Starter Kit bortsett fra at fire høyt spesialiserte verktøy har blitt erstattet, noe som gjør settet bedre rustet for noe mer avansert profesjonelt arbeid. Vår beslutning om verktøyene er basert på det faktum at når en person først har begynt å jobbe med våpen, oppdager de raskt at de får med seg et bredere utvalg av våpen enn de hadde forventet, og at visse, tilsynelatende "normale", monterings- og demonteringstrinn kan være vanskelig uten riktig verktøy. (Dette settet er av største verdi for alle som driver med våpenavblåsing og generell reparasjonsservice.) Colt-håndvåpen vil være en del av livet ditt. Når du demonterer enten store eller små revolvere, må ejektoren fjernes fra sylinderen før polering, blåsing eller service. Colt-verktøyet i settet gjør denne ellers kile jobben ganske enkel. I tillegg gjør verktøyet det enklere å fjerne eller installere tette 1911 Auto-foringer. Bolt extractor tang kan bare bli verdsatt av en som har kjempet for fjerning og installasjon av en stiv avtrekker på en Enfield, Springfield, Mauser eller lignende bolt. . . Spesielt når hendene dine er "våpensmed fete". Leveres med illustrerte instruksjoner som viser hvordan du bruker dem når du tar dem av eller på. Magasinholderhetter på Ithaca 37-er, Winchester Model 12-er og lignende krever definitivt den spesielle Winchester Model 12-nøkkelen for å fjerne. Vil takle det tøffeste. Så er det den lille 7/64" Speed-Head (Ball End) Socket Wrench. Første gang du støter på en scope-ring (som på nyere Redfields) med unbrakoskruer på undersiden av ringene, vil du rose dette verktøyet for livredderen det er. Monterings-/demonteringssettet inneholder følgende verktøy: nr. 100 parallelltang; 1" nylon/messinghammer; nr. 81 MAGNA-TIP® skrutrekker; Skrutrekkerbits nr.1 - 2 - 6 - 00 - 10 - 20 og 30; Instrumentskrutrekkere i to størrelser; Main Spring skrustikke; MF134 India Stone; M-16 børste; 1/8" x 6" Pin Punch; 5/32" x 6" Pin Punch; 1/16" Starter Punch; 3/32" Starter Punch; Brownells erstatningsstift-punch-sett; 2" Erstatningsstansesortiment; Nylon/messing Driftpinnestansesett; Gunsmith Benk Kniv; 8" No. 2 Cut Hand File; Sight Base File; Brownells Colt Pistolnøkkel; Brownells Winchester modell 12 skiftenøkkel; Bolt Spring Extractor Tang; Skrue Check'r; 7/64" Speed-Hex-nøkkel (ballende) og settboks.
9599 NOK 0 kr 9 599,00 *
Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
Spesifikasjoner: Make: Universal Handguns

Attributes

Make: Universal Handguns Leveringsvekt: 3,583kg Høyde: 762mm Bredde: 287mm Lengde: 401mm

Elementdetaljer

Made in USA




With Special Tools For Colts & Mausers
The 30 tools and bits in the Assembly/Disassembly Kit are basically the same as those in the Basic Starter Kit except that four highly specialized tools have been substituted, making the Kit better equipped for somewhat more advanced professional work. Our decision on the tools is based on the fact that once a person gets started doing some gunsmithing, they quickly discover they are being brought a wider variety of guns than they had anticipated and that certain, seemingly "normal", assembly and disassembly steps can be difficult without the right tools. (This Kit is of paramount value to anyone doing gun rebluing and general repair service.) Colt handguns will be a part of your living. Whenever you disassemble either large or small frame revolvers, the ejector must be removed from the cylinder prior to polishing, bluing or servicing. The Colt Tool in the Kit makes this otherwise ticklish job quite simple. Plus, the tool makes it easier to remove or install tight 1911 Auto bushings. The Bolt Extractor Pliers can only be appreciated by one who has fought the removal and installation of a stiff extractor on an Enfield, Springfield, Mauser or similar bolt . . . Especially when your hands are "gunsmith greasy". Comes with illustrated instructions showing how to use when taking them off or putting them on. Magazine retaining caps on Ithaca 37's, Winchester Model 12's and similar, positively require the special Winchester Model 12 Wrench to remove. Will handle the toughest. Then there is the little 7/64" Speed-Head (Ball End) Socket Wrench. The first time you encounter a scope ring (like on newer Redfields) with Allen head screws on the bottom side of the rings, you will praise this tool for the lifesaver it is. Assembly/Disassembly Kit contains the following tools: No. 100 Parallel Pliers; 1" Nylon/Brass Hammer; No. 81 MAGNA-TIP® Screwdriver; Screwdriver Bits Nos. 1 - 2 - 6 - 00 - 10 - 20 and 30; Two sizes Instrument Screwdrivers; Main Spring Vise; MF134 India Stone; M-16 Brush; 1/8" x 6" Pin Punch; 5/32" x 6" Pin Punch; 1/16" Starter Punch; 3/32" Starter Punch; Brownells Replacement Pin-Punch Set; 2" Replacement Punch Assortment; Nylon/Brass Drift Pin Punch Set; Gunsmith Bench Knife; 8" No. 2 Cut Hand File; Sight Base File; Brownells Colt Pistol Wrench; Brownells Winchester Model 12 Wrench; Bolt Spring Extractor Pliers; Screw Check'r; 7/64" Speed-Hex (Ball-end) Wrench and Kit Box.
Nyhetsbrev