Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge
080755000
With Special Tools For Colts & Mausers
The 30 tools and bits in the Assembly/Disassembly Kit are basically the same as those in the Basic Starter Kit except that four highly specialized tools have been substituted, making the Kit better equipped for somewhat more advanced professional work. Our decision on the tools is based on the fact that once a person gets started doing some gunsmithing, they quickly discover they are being brought a wider variety of guns than they had anticipated and that certain, seemingly "normal", assembly and disassembly steps can be difficult without the right tools. (This Kit is of paramount value to anyone doing gun rebluing and general repair service.) Colt handguns will be a part of your living. Whenever you disassemble either large or small frame revolvers, the ejector must be removed from the cylinder prior to polishing, bluing or servicing. The Colt Tool in the Kit makes this otherwise ticklish job quite simple. Plus, the tool makes it easier to remove or install tight 1911 Auto bushings. The Bolt Extractor Pliers can only be appreciated by one who has fought the removal and installation of a stiff extractor on an Enfield, Springfield, Mauser or similar bolt . . . Especially when your hands are "gunsmith greasy". Comes with illustrated instructions showing how to use when taking them off or putting them on. Magazine retaining caps on Ithaca 37's, Winchester Model 12's and similar, positively require the special Winchester Model 12 Wrench to remove. Will handle the toughest. Then there is the little 7/64" Speed-Head (Ball End) Socket Wrench. The first time you encounter a scope ring (like on newer Redfields) with Allen head screws on the bottom side of the rings, you will praise this tool for the lifesaver it is. Assembly/Disassembly Kit contains the following tools: No. 100 Parallel Pliers; 1" Nylon/Brass Hammer; No. 81 MAGNA-TIP® Screwdriver; Screwdriver Bits Nos. 1 - 2 - 6 - 00 - 10 - 20 and 30; Two sizes Instrument Screwdrivers; Main Spring Vise; MF134 India Stone; M-16 Brush; 1/8" x 6" Pin Punch; 5/32" x 6" Pin Punch; 1/16" Starter Punch; 3/32" Starter Punch; Brownells Replacement Pin-Punch Set; 2" Replacement Punch Assortment; Nylon/Brass Drift Pin Punch Set; Gunsmith Bench Knife; 8" No. 2 Cut Hand File; Sight Base File; Brownells Colt Pistol Wrench; Brownells Winchester Model 12 Wrench; Bolt Spring Extractor Pliers; Screw Check'r; 7/64" Speed-Hex (Ball-end) Wrench and Kit Box.
9799 9799 1 NOK
Produktnr.: 080755000
BROWNELLS ASSEMBLY/DISASSEMBLY KIT De 30 verktøyene og bitene i Assembly/Disassembly Kit er i hovedsak de samme som i Basic Starter Kit, bortsett fra at fire svært spesialiserte verktøy har blitt byttet ut, noe som gjør settet bedre utstyrt for noe mer avansert profesjonelt arbeid. Vårt valg av verktøy er basert på det faktum at når en person begynner med litt børsemakerarbeid, oppdager de raskt at de får inn et bredere utvalg av våpen enn de hadde forventet, og at visse, tilsynelatende "normale", monterings- og demonteringssteg kan være vanskelige uten riktige verktøy. (Dette settet er av ypperste verdi for alle som driver med våpenblånering og generell reparasjonstjeneste.) Colt-håndvåpen vil bli en del av din hverdag. Når du demonterer enten store eller små ramme-revolvere, må utstøteren fjernes fra sylinderen før polering, blånering eller service. Colt-verktøyet i settet gjør denne ellers vanskelige jobben ganske enkel. I tillegg gjør verktøyet det lettere å fjerne eller installere stramme 1911 Auto-busker. Bolt Extractor Pliers kan bare settes pris på av en som har kjempet med fjerning og installasjon av en stiv ekstraktor på en Enfield, Springfield, Mauser eller lignende bolt... Spesielt når hendene dine er "børsemakergråsete". Kommer med illustrerte instruksjoner som viser hvordan du bruker dem ved avmontering eller påsetting. Magasinholderkapsler på Ithaca 37, Winchester Model 12 og lignende krever absolutt det spesielle Winchester Model 12-verktøyet for å fjerne. Håndterer det tøffeste. Så er det den lille 7/64" Speed-Head (Ball End) Socket Wrench. Første gang du møter en kikkertsikteringsring (som på nyere Redfields) med Allen hodeskruer på undersiden av ringene, vil du prise dette verktøyet som en livredder. Assembly/Disassembly Kit inneholder følgende verktøy: No. 100 Parallel Pliers; 1" Nylon/Brass Hammer; No. 81 MAGNA-TIP® Skrutrekker; Skrutrekkerbits nr. 1 - 2 - 6 - 00 - 10 - 20 og 30; To størrelser instrument-skrutrekkere; Hovedfjærtvinge; MF134 India Stone; M-16 Børste; 1/8" x 6" Stiftutdriver; 5/32" x 6" Stiftutdriver; 1/16" Starter Punch; 3/32" Starter Punch; Brownells Replacement Pin-Punch Set; 2" Replacement Punch Assortment; Nylon/Brass Drift Pin Punch Set; Gunsmith Bench Knife; 8" No. 2 Cut Hand File; Sight Base File; Brownells Colt Pistol Wrench; Brownells Winchester Model 12 Wrench; Bolt Spring Extractor Pliers; Screw Check'r; 7/64" Speed-Hex (Ball-end) Wrench og Kit Box.
9799 NOK 0 kr 9 799,00 *
Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
Spesifikasjoner: Make: Universal Handguns

Attributes

Make: Universal Handguns Leveringsvekt: 3,583kg Frakthøyde: 762mm Fraktbredde: 287mm Fraktlengde: 401mm

Elementdetaljer

Made in USA



With Special Tools For Colts & Mausers
The 30 tools and bits in the Assembly/Disassembly Kit are basically the same as those in the Basic Starter Kit except that four highly specialized tools have been substituted, making the Kit better equipped for somewhat more advanced professional work. Our decision on the tools is based on the fact that once a person gets started doing some gunsmithing, they quickly discover they are being brought a wider variety of guns than they had anticipated and that certain, seemingly "normal", assembly and disassembly steps can be difficult without the right tools. (This Kit is of paramount value to anyone doing gun rebluing and general repair service.) Colt handguns will be a part of your living. Whenever you disassemble either large or small frame revolvers, the ejector must be removed from the cylinder prior to polishing, bluing or servicing. The Colt Tool in the Kit makes this otherwise ticklish job quite simple. Plus, the tool makes it easier to remove or install tight 1911 Auto bushings. The Bolt Extractor Pliers can only be appreciated by one who has fought the removal and installation of a stiff extractor on an Enfield, Springfield, Mauser or similar bolt . . . Especially when your hands are "gunsmith greasy". Comes with illustrated instructions showing how to use when taking them off or putting them on. Magazine retaining caps on Ithaca 37's, Winchester Model 12's and similar, positively require the special Winchester Model 12 Wrench to remove. Will handle the toughest. Then there is the little 7/64" Speed-Head (Ball End) Socket Wrench. The first time you encounter a scope ring (like on newer Redfields) with Allen head screws on the bottom side of the rings, you will praise this tool for the lifesaver it is. Assembly/Disassembly Kit contains the following tools: No. 100 Parallel Pliers; 1" Nylon/Brass Hammer; No. 81 MAGNA-TIP® Screwdriver; Screwdriver Bits Nos. 1 - 2 - 6 - 00 - 10 - 20 and 30; Two sizes Instrument Screwdrivers; Main Spring Vise; MF134 India Stone; M-16 Brush; 1/8" x 6" Pin Punch; 5/32" x 6" Pin Punch; 1/16" Starter Punch; 3/32" Starter Punch; Brownells Replacement Pin-Punch Set; 2" Replacement Punch Assortment; Nylon/Brass Drift Pin Punch Set; Gunsmith Bench Knife; 8" No. 2 Cut Hand File; Sight Base File; Brownells Colt Pistol Wrench; Brownells Winchester Model 12 Wrench; Bolt Spring Extractor Pliers; Screw Check'r; 7/64" Speed-Hex (Ball-end) Wrench and Kit Box.
Nyhetsbrev