Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge

EGW
TAURUS G2, G3, PT709 AND TX22 VORTEX VIPER/VENOM SIGHT MOUNT

841370117543 296000651
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with the mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
999 999 1 NOK
Produktnr.: 296000651
EGW SIGHT MOUNT FOR VORTEX VIPER/VENOM FITS TAURUS G2/G3 BLACK
Produsentnr.: 49291 841370117543 EGW rødpunktsikter er ment å installeres fra venstre mot høyre (med løpet pekende fremover). Sporet har en progressiv avsmalning for å tillate enklere installasjon. Bare fjern baksiktet på våpenet ditt og erstatt det med monteringen for å kunne montere ditt Vortex Viper/Venom, Burris FastFire eller Docter rødpunktsikte. Du kan når som helst ta av monteringen og erstatte baksiktet. Monteringsutstyr inkludert. Installasjonsinstruksjoner Fjern baksiktet* Installer EGW Sight Mount i sporet Stram til sett-skruen (hvis aktuelt) Plasser rødpunktsiktet på EGW Sight Mount (å legge en liten bit papir mellom rødpunktsiktet og siktemonteringen vil gjøre fjerning enklere og vil holde Loctite borte fra rødpunktsiktet.) Påfør blå Loctite på de medfølgende monteringsskruene Stram monteringsskruene til 15in/lbs 2 knappehodekapselskruer - Levert for Vortex Viper og Venom sikter 2 flatkapselskruer - Levert for Burris FastFire og Docter sikter Skruene som følger med denne monteringen krever en 5/64'' unbrakonøkkel for installasjon. Modifikasjon av våpenet ditt kan oppheve produsentens garanti. Dette produktet bør installeres og sjekkes av en kvalifisert børsemaker. Ingen ansvar er uttrykt eller antydet for skade eller skade som kan oppstå fra feil installasjon eller bruk av dette produktet.
999 NOK 3 kr 999,00 *
Leveringstid ca. 14-21 dager.
3 stk. på lageret i USA
Spesifikasjoner: Farge: Black Make: Taurus Material: Aluminum Modell: PT-111, G3, G2C, TX22, PT-740, PT-709, PT-140 G2, G2S Number of Bases: 1-Piece Style: Tactical

Attributes

Farge: Black Make: Taurus Material: Aluminum Modell: PT-740,G2S,PT-111,PT-140 G2,TX22,PT-709,G3,G2C Number of Bases: 1-Piece Style: Tactical Leveringsvekt: 0,045kg Frakthøyde: 25mm Fraktbredde: 76mm Fraktlengde: 140mm

Elementdetaljer

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with the mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Nyhetsbrev