Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Kompakt og solid montering for Trijicon RMR
EGW S&W M&P TRIJICON RMR SIGHT MOUNT er laget av høykvalitets 7075 aluminium med en matt svart hardcoat som gir både styrke og et stilrent utseende.
Produktdetaljer:
- Materiale: 7075 Aluminium
- Belegg: Matt svart hardcoat
- Totallengde: 1.780"
- Totalt bredde: 1.1"
- Monteringsutstyr: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw
- Rødpunkt kompatibilitet: Trijicon RMR
Denne monteringen passer til:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Denne monteringen passer ikke til:
- Smith & Wesson M&P Shield (Vår montering er for bred for å passe Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Vil ikke passe til M&P .22 Compact. Smith and Wessons bakre sikter kan variere i dimensjoner, noe som kan føre til installasjonsvansker. Vennligst vær oppmerksom på dette når du bestiller.
Monteringene bør installeres og sjekkes av en kvalifisert våpensmed. Ingen ansvar er uttrykt eller underforstått for skade eller skade som kan oppstå fra feil installasjon eller bruk av dette produktet.
Installasjonsinstruksjoner:
- Fjern bakre sikte*
- Installer EGW Sight Mount i dovetail
- Stram setteskruen (hvis aktuelt)
- Plasser rødpunkt-siktet på EGW Sight Mount (å legge et lite papir mellom rødpunkt-siktet og siktemonteringen vil gjøre det lettere å fjerne og holde Loctite unna rødpunkt-siktet).
- Påfør blå Loctite på de medfølgende monteringsskruene
- Dra til monteringsskruene til 15in/lbs
*Bakre sikteverktøy anbefales sterkt.