All I can say is wow. I installed the sear in my mp Shield 9 and the trigger pull is so light it almost frightened me when I fired it for the first time. It dose what it says. I don't have a gauge, but it is very apparent it's lighter.

First, shipping was quick. Maybe not "Amazon quick" but close. The installation was pretty easy although it never hurts to watch a good YouTube video. Today I got to test the upgrade and I was surprised by the smoothness of the trigger and the reduced pull weight. It felt a bit like the first time I drove a Corvette; it tried to get away from me. It takes a few rounds to get used to but then the groups will tighten up significantly. This should also help those who are fighting the "low and left" issue with their Shields. The is a great compromise for those who want a better trigger but would rather not install that funny red lever in their gun and spend three times the money for the full kit.

Reduced the pull on my 2.0 9mm from 5.5lbs to 4.25lbs. with no other modifications to the gun. Slight decreas in pre travel and reset, but I doubt you would notice it when shooting.

This is the second Apex sear I have installed in a M&P 45 . This little part makes ALL the difference in the world !!! It makes a very good pistol with a sub par trigger into what a M&P should be.



The hardest part was getting the roll pins out .Also be careful with the factory sear there is a tiny spring under it. Wouldn't have a M&P without putting the Apex hard sear in!!

This upgrade made for a much lighter, more manageable trigger. Had my regular gunsmith install it on my unfired, new Shield .45. I could not be happier. I was thinking of adding a new trigger but it really isn't necessary.

I have both an M&P 45 Compact and a 9mm Shield, and purchased one of these sears for each. Both installed with only a pin punch, but the Shield was a little trickier. For the Shield, I had to remove both the sear housing and the locking block from the frame, and I did notice some plastic shavings when removing and reinstalling the sear housing (clearly not a fault of the product, but something to look out for during installation). But the results after installing them were impressive: in each case, the trigger breaks a little later in its travel, the reset is shorter, the overtravel is shorter,and the trigger pull is a little lighter. Since you won't be modifying any safety mechanisms, installation is relatively safe, and the results are well worth it. There will still be some initial grit from the trigger bar acting on the striker block plunger, but aside from that the trigger break is much nicer. If I ever purchase another M&P, I'm putting this sear in it.

Replacing the stock sear with this made the trigger what it should be, nice and crisp. Much better than original. Add the firing pin block kit and make it even better. The hard sear alone gets you 75% there though.

Took my new M&P 45 (~ 50 rnds shot) to the LGS and had this put in. It was done in less than 5 min, and the trigger pulls @ 5# on the button! My only complaint is why M&P doesn't fix this in the first place saving us all $50...

I bought this part to use in my M&P 9mm & the sear is noticeably TOO short for the trigger bar to engage! No clue if this is for an older built model or a compact or what, but it WOULD NOT WORK! The sear that came with the Apex kit worked fine, go figure.

HOLY!! I bought this and the spring kit and installation was a zip. I'm no gunsmith but this is just a drop in job as long as you have roll pin punches. The new sear and sear spring combined brought my new M&P pull down from 6.5lbs to 4.5lbs and only took about 15 minutes to do. Trigger reset spring dropped the pull another pound to a feather light 3.5. There's still some mush in it but that should clear up in time.

The sear is machines steel, not MIM. The cam surface isn't polished so I touched it up a bit using a emery board but did not touch the surface which contacts the striker. The point of contact is further back than the stock sear (see pic) and a much lower angle. The break point is further back than stock which leaves less overtravel but don't be fooled into thinking this is a 1911 trigger. It's significantly better but the surfaces should have been polished first!

Works just as advertised. I was going to trade in my M&P 45 on something else until I installed this sear.

I have put Apex sears in every M&P I've owned, my current 9mm has 20,000 rounds on the sear with no issues. The improvement to the trigger is immediate, consistent and lasts and installation is a snap. You really couldn't ask for more.

I mostly use my M&P 9mm for target shooting. This new sear has not only increased the speed but has also allowed me to be more accurate in my shooting. I did polish the sear before installing it.

Drop in part that does just what it says. It reduces the trigger pull and makes for a much better feeling trigger. I put one in my M&P 40C, and my 45F, now I'm putting one in my dads 45F and my brothers carry 40.

The Apex sear for the M&P 45 is perfect. After install and without any spring or other part modification changes, the trigger breaks at a consistent 4.5 lbs. Of course this is on an already well broken in .45. CC

Easy to install and greatly reduced trigger pull (now about 3lb). I also polished the trigger bar and installed the Apex reduced power return spring. The trigger is now very smooth with a very tactile reset.