Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge

EGW
S&W K, L, N, X FRAME REVOLVERS VORTEX RAZOR SIGHT MOUNT

841370113019 296000691
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.  
999 999 1 NOK
Produktnr.: 296000691
EGW SIGHT MOUNT FOR VORTEX RAZOR FITS S&W K, L, N, X FRAME BLACK
Produsentnr.: 49438 841370113019 Fjern enkelt baksiktet på våpenet ditt og erstatt det med EGW-monteringen for å kunne montere ditt Vortex Razor, C-More RTS eller STS rødpunktsikte. Du kan når som helst ta av monteringen og sette baksiktet tilbake. Monteringsutstyr inkludert. Installasjonsinstruksjoner Fjern baksiktet* Installer EGW Sight Mount i svalehalen Stram sett skruen (hvis aktuelt) Plasser rødpunktsiktet på EGW Sight Mount (ved å legge en liten bit papir mellom rødpunktsiktet og siktemonteringen vil gjøre fjerningen enklere og vil holde Loctite borte fra rødpunktsiktet.) Påfør blå Loctite på de medfølgende monteringsskruene Dra monteringsskruene til med 15in/lbs Skruene som følger med denne monteringen krever en 5/64'' unbrakonøkkel for installasjon. Denne monteringen passer til: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers Dersom revolveren din ikke er boret og gjengesnittet vil ikke denne monteringen fungere. Den beste måten å verifisere at den er/ikke er boret og gjengesnittet er å åpne tønnehuset og sjekke ribben under. Det bør være gjennomgående hull som er boret og gjengesnittet. Hvis det ikke er det (som bildet over) vil ikke denne monteringen fungere uten at du får boret og gjengesnittet våpenet. Du kan få en kompetent og kvalifisert børsemaker til å bore og gjengesnitte toppremmen med det standard S&W hullmønsteret som vil tillate deg å bruke vår montering.
999 NOK 1 kr 999,00 *
Leveringstid ca. 14-21 dager.
1 stk. på lageret i USA
Spesifikasjoner: Farge: Black Make: Smith & Wesson Material: Aluminum Modell: K Frame, L Frame, N Frame, X Frame Number of Bases: 1-Piece Style: Tactical

Attributes

Farge: Black Make: Smith & Wesson Material: Aluminum Modell: N Frame,K Frame,X Frame,L Frame Number of Bases: 1-Piece Style: Tactical Leveringsvekt: 0,045kg Frakthøyde: 25mm Fraktbredde: 76mm Fraktlengde: 140mm

Elementdetaljer

Made in USA



Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.  
Nyhetsbrev