Attributes
- Material:
Steel
- Style:
Installation Tool
- Leveringsvekt: 0,612kg
- Frakthøyde: 58mm
- Fraktbredde: 84mm
- Fraktlengde: 272mm
Steel
Installation Tool
Produktnr.: 488000006
Produsentnr.: NONE
Presisjonsjusterbar jig opprettholder riktig bormaskinjustering for å sikre korrekt plassering av hullet for bakre svingestud. Passer til enhver størrelse kolbe og sentrerer seg automatisk for perfekt justering av studhullet. Filtramming forhindrer skader på ferdigstilte kolber. Inkluderer 5/32" diameter karbonstål bor med en spesiell avlastningstipp for å hindre splintering av tre og brudd under boring. Justerbar bor-dybdeindikator forhindrer for dyp boring som kan ødelegge hullet. For bruk med håndholdt bormaskin. Perfekt for høyvolum verksteder eller nybegynnere som nettopp har startet.Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
SLING SWIVEL DRILL JIG fra KLEINENDORST er en presisjonsjusterbar jig som opprettholder riktig justering av bor for å sikre korrekt plassering av bakre swivel stud hull. Den passer til alle størrelser av stokk og sentrerer seg automatisk for perfekt hulljustering.
Jigen har en filtforing som forhindrer riper på ferdigbehandlede stokker. Den inkluderer en 5/32" diameter karbonstål bor med en spesiell avlastningstipp for å forhindre splintering av treverket og utfall under boring. En justerbar bore-dybdeindikator hindrer boring for dypt og ødelegger hullet.
Den er designet for bruk med håndholdte bor og er perfekt for både høyt volum verksteder og nybegynnere som nettopp har startet.
Steel
Installation Tool
Best Sling Swivel Jig 26.05.2013
Kleinendorst has the best tool for accurately drilling sling swivel stud holes in the butt of a rifle or shotgun stock! The other designs are a lot of foolishness for mediocre results. I assigned 4 out of 5 in the rating system because of one issue that needs to be addressed with this jig. A normal 3/4" threaded sling swivel stud (suitable for wood or synthetic stocks) has a mostly threaded shank with a small portion that is not threaded and slightly larger in diameter. Kleinendorst supplies a drill that will handle both diameters in one step and works wonderfully! However, after that is done and you screw the sling swivel stud in the stock (with or without one of those little black or white plastic spacers) you notice that your very accurately placed hole is not counter-bored. The part of the sling swivel stud that you see when it is screwed in to the stock does not fit flush when you view the stock from the side! There needs to be a specialized Forstner-type bit with an appropriate diameter pin in the middle (centering in the wonderfully accurate hole already there) for counter-boring a tiny bit of stock material and thereby allowing the sling swivel stud to seat flush in the stock. Thanks for a great product!
I recommend this Drill Jig 18.03.2010
I recommend this product: 488-000-006 KLEINENDORST SLING SWIVEL JIG
To date I have successfully drilled three stocks with it with very good results. The tool is very robust (built well) and capable. I opted to use a fine file however to put a few measurement nicks on the stop rod; e.g. 3" mark to offset the fixed jig block for visible assuredness to stand off repeatable from the butt plate each time with certainty. I did this putting the stop rod against a square then measured for this mark-purely optional. The set screw works as intended. More difficult, my 3rd task required drilling a stock for a military style two screw swivel plate. It worked fine performing the math for the second hole. I am very pleased over all. Read the instructions and start patiently to get the hang of it. I believe you will like it as I do.
Vi opplevde en feil under innlasting av dette innholdet. Vennligst last inn siden på nytt for å fortsette. Hvis problemet vedvarer, ta kontakt med kundeservice.