Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge
696177784845 100041436
An Easy Way to Level Your Optic
The human eye can't detect whether or not a scope reticle is level if the degree is off by 3 degrees or less, but if your scope is off by just 3 degrees, then you're in trouble when it comes to making in-reticle adjustments for those long-range shots. The Fix It Sticks Scope Jack Leveling Tool is designed to get your scope set up right, and it works with any 1/4-inch driver! All you have to do is mount the jack to the Picatinny rail sitting underneath your riflescope. Then turn the drive handle until the arm on the jack engaged with the flat spot underneath your windage and elevation turrets. This ensures that your scope is perfectly level, and the jack will maintain pressure on this flat spot while you tighten your rings down. In order for the Fix It Sticks Scope Jack Leveling Tool to work, you have to have a short section of Picatinny rail sitting just underneath your scope body. Depending on how much clearance is available, you might have to take off the thumb screw and clamp to slide the jack onto the mounting surface from the side. Fix It Sticks says that there must be at least 1/4 inch of clearance to use the jack.
949 949 1 NOK
Produktnr.: 100041436
FIX IT STICKS SCOPE JACK LEVELING TOOL
Produsentnr.: FISSJACK 696177784845 Det menneskelige øyet kan ikke oppdage om et siktekorn er nivellert eller ikke hvis graden er av med 3 grader eller mindre, men hvis ditt sikte er av med bare 3 grader, da vil du få problemer når det kommer til å gjøre justeringer innenfor siktekornet for de lange skuddene. Fix It Sticks Scope Jack Leveling Tool er designet for å sette opp siktet ditt riktig, og det fungerer med enhver 1/4-tommers driver! Alt du trenger å gjøre er å montere jekken på Picatinny-skinnen som sitter under kikkertsiktet ditt. Deretter vri på driverhåndtaket til armen på jekken griper inn med det flate området under vind- og høydejusteringstårnene dine. Dette sikrer at siktet ditt er perfekt nivellert, og jekken vil opprettholde trykk på dette flate området mens du strammer ringene dine. For at Fix It Sticks Scope Jack Leveling Tool skal fungere, må du ha en kort seksjon av Picatinny-skinne som sitter rett under kroppen på kikkertsiktet ditt. Avhengig av hvor mye klaring som er tilgjengelig, må du kanskje ta av tommelskruen og klemmen for å skyve jekken på monteringsoverflaten fra siden. Fix It Sticks sier at det må være minst 1/4 tommers klaring for å bruke jekken.
949 NOK 135 kr 949,00 *
Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

Attributes

Leveringsvekt: 0,045kg Frakthøyde: 25mm Fraktbredde: 76mm Fraktlengde: 152mm




An Easy Way to Level Your Optic
The human eye can't detect whether or not a scope reticle is level if the degree is off by 3 degrees or less, but if your scope is off by just 3 degrees, then you're in trouble when it comes to making in-reticle adjustments for those long-range shots. The Fix It Sticks Scope Jack Leveling Tool is designed to get your scope set up right, and it works with any 1/4-inch driver! All you have to do is mount the jack to the Picatinny rail sitting underneath your riflescope. Then turn the drive handle until the arm on the jack engaged with the flat spot underneath your windage and elevation turrets. This ensures that your scope is perfectly level, and the jack will maintain pressure on this flat spot while you tighten your rings down. In order for the Fix It Sticks Scope Jack Leveling Tool to work, you have to have a short section of Picatinny rail sitting just underneath your scope body. Depending on how much clearance is available, you might have to take off the thumb screw and clamp to slide the jack onto the mounting surface from the side. Fix It Sticks says that there must be at least 1/4 inch of clearance to use the jack.
Nyhetsbrev