Din handlekurv er tom.

Handlekurv

37 17 00 00

Meld på nyhetsbrev

Triple-K
REMINGTON 7400 10RD MAGAZINE 30-06 SPRINGFIELD

730745000491 486000002

More Rounds Than Factory Magazine All-Steel Body Gives Rigidity

Durable high-capacity magazine provides a long service life and holds ten rounds for fewer reloads when shooting your Remington 740, 742, 750, or 7400. Folding, leaf spring and nylon follower ensure reliable feeding. Available in .30-06 and .308.

SPECS: Steel, blued. Approximately 31⁄2" (9cm) wide, 37⁄16" (8.7cm) high, 1" (2.54cm) thick. Fits Remington 740, 742, 750 & 7400.

Mer...

Flere runder enn fabrikkmagasin All-Steel Body gir stivhet

Slitesterkt magasin med høy kapasitet gir lang levetid og holder ti runder for færre lastinger når du skyter Remington 740, 742, 750 eller 7400. Brett, bladfjær og nylonfølger sikrer pålitelig fôring. Tilgjengelig i .30-06 og .308.

SPECS: stål, blått. Omtrent 31⁄2 "(9 cm) bred, 37⁄16" (8,7 cm) høy, 1 "(2,54 cm) tykk. Passer til Remington 740, 742, 750 & 7400.

Mer...

Kundevurderinger for Triple-K REMINGTON 7400/742 MAGAZINE 30-06 SPRINGFIELD 10RD STEEL BLA

Antall vurderinger: 16
Fra brownells.com: 16
Gjennomsnittsvurdering: 2,9

does the job (21.04.2010)

bought for my rem750 in .270 win. ammo loads well, mag fits like a dream and no problems with jams, ftf, etc up to this point.
numbers don't lie, 10>4, hope to be using these for a while

Awesome Purchase (22.06.2010)

This is an awesome addition to my Model 742 and let me tell you, I feel much more comftorable in the woods hunting hogs than with the stock 4 round clip. I fired off 20 rounds in each of the two clips that I purchased and both fired and loaded flawlessly. The one draw back is that I have to hold the action open when I insert the clip in order for it to be fully inserted. Not a big deal for me and I would buy this product again and again.

Works well in 7600 (10.07.2010)

The lack of bolt hold open is a non-issue in the Remington 7600. My particular magazine had a rough start with some extra metal that caught on case mouths as they were fed, but 30 seconds with a Dremmel tool solved that nicely. I traced the contour from the front of a factory mag onto this one and ground to match. Too bad Triple-K didn't do the same at the factory. After cleaning up the front of the magazine I've had no further problems. The spring holds tension well when left loaded. My example has remained loaded for the last 6 years and still feeds rounds as fast as I can shuck the action.

979M REM 7400 10rd magazine (28.05.2011)

I was glad of purchase I made from Italy, so that my friends who have also a Remington 7400 luxury carbine .30-06 I prayed for them to buy the magazine from 10 shots.

Not perfect. (12.09.2011)

I bought 2 of these for my remington 7400 to use at the gun range, the quality is ok but not as good as factory. It needs a little manhandling to get it fully seated into the rifle. I would've like to seen all metal used in the construction (the follower is plastic and has alot of play front to back) The biggest problem I have with it is that it holds the bullets down too long and they mash into the bottom of the feed ramp causing a jam and deformed bullit tips.

Triple K Version is generally good (27.11.2011)

I use it in my 742, 30-06. I initially found that it bound my bolt.
I needed to take it to the grinding wheel (Dremmel) to match my original Remington clip. A few strokes with the grinder and now it feeds properly.

I would recommend it.

not again (19.01.2012)

bought 2 for 742 30-06, fowler poped out, no front tabs to hold fowler in, sides misscut,
sides not bent in at a proper curve to hold rounds, not worth the postage to return to triple k

Good buy. (29.06.2012)

Good buy. ran 50 rounds through it in one session, no misfeeds, worked like a champ.

will not chamber 3 rounds in a row. (03.10.2012)

I have cleaned my rifle, also cleaned both of my 4 and 10 round mags. My rifle shot fine with the 4 round mag, but it would not shoot 3 times in a row with the 10 round mag. It even broke to tip off of 1 of my Ballistic Tip bulletswith the 10 round mag in, the action feels slower like it is dragging. Putting both clips aft end towards each other you can see the original mag is a mil or 2 wider at the feed point. Perhaps thats the problem? Maybe it can be bent?

Poor Quality Magazines (16.09.2014)

Recently bought two of these 10 round magazines for my 30-06.

I first time I put the rounds into one of them,the bottom cap came off, the spring flew out and the rounds ended up on the turf. Was pretty embarrassed at the range..The other magazine that does work is exceptionally tight fitting and difficult to get out of the gun..Not happy at all about this purchase

Tony Magazzi

7400 rifle (11.11.2014)

Bought this for a REM 7400 the clip holds the shell down to long and jams every time. The indents on the side of the clip that raise the bullet is to far forward about a 3/16 in. compared to the clip I use a 280. Might work with bullets that have a very short nose on them or other models.

Very reliable (11.02.2016)

I had a very hard time finding spare or aftermarket magazines for my 7400, either standard or high capacity. It can be a pain at the range to constantly stop shooting and reloading a single four round magazine. It's hard to relax and enjoy what you're doing when you need to constantly stop and reset everything. I was happy to finally find one at Brownells. I ordered two of the ten round magazines, and I love them both. They both work perfectly, and they fit and function more smoothly than the original. Reading the other reviews, it seems that people either love them or hate them. It could be that they have some quality control issues, and I might have caught them on a good day. It's possible they only work well in the 7400 / 7600 models, or maybe just in mine. All I can offer an opinion on are the ones I received, and I'm firmly in the "love them" group. I'll be ordering a couple more as soon as they're back in stock.

Doesn't worn in Model 742 (28.07.2016)

These mags don't load, seat & cause the bolt to jam in Remington Model 742. None of the 7400 series mags seem to fit, load or properly operate either. Keep looking for actual Remington 742 mags otherwise you're just waisting time & money.

Trash (01.03.2018)

The bolt won't cycle if there's more than one round in the mag, won't take more than 5 rounds, the mag takes a lot of force to go into the well which means it doesn't fit.. Also, there's no bolt release on it. I don't know whether to return them or just throw them away because I know it's my civic duty.

Puts bullets in my gun (09.03.2018)

Shipping was a little on the slower side for standard shipping but I was in no rush to get it anyway but it does what a clip is supposed to I put it in my gun and it gave my gun bullets with no jams so there is nothing to complain about

Not bad but needs improvement (12.08.2018)

I had purchased mine and was stoked to get it but first day at the range and it jammed on every round. I did figure out why, it seems the indents in the side of it were to far forward to assist the round into the feed ramps on my 7400, I was able to get some durable epoxy to stick and made a spot on each side to assist the rounds. The quality seems pretty good, put together well just the slight tweaks and it would be a 5 star. Other then the slight issue it works pretty good and fits pretty well but hope who ever makes them can see these and make the proper improvements to make it a great magazine.

Les 16 flere anmeldelser fra brownells.com

649 649 1 NOK

Produktnr.: 486000002
Triple-K REMINGTON 7400/742 MAGAZINE 30-06 SPRINGFIELD 10RD STEEL BLA
Produsentnr.: 979M 730745000491 Slitesterkt magasin med høy kapasitet gir lang levetid og holder ti runder for færre lastinger når du skyter Remington 740, 742, 750 eller 7400. Brett, bladfjær og nylonfølger sikrer pålitelig fôring. Tilgjengelig i .30-06 og .308.

649 NOK 28 kr 649,00 *

Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

Spesifikasjoner: Capacity: 10-Round Cartridge: 30-06 Springfield Finish: Black Make: Remington Material: Steel Modell: 7400 Type låskasse: Semi-Auto Antall: 1

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Attributes

Action Type: Semi-Auto Cartridge: 30-06 Springfield Finish: Black Kapasitet: 10-Round Make: Remington Material: Steel Modell: 7400 Leveringsvekt: 0,159kg Høyde: 38mm Bredde: 114mm Lengde: 180mm

Elementdetaljer

Made in USA
US eksport klassifisering: 0A501.x

More Rounds Than Factory Magazine All-Steel Body Gives Rigidity

SPECS: Steel, blued. Approximately 31⁄2" (9cm) wide, 37⁄16" (8.7cm) high, 1" (2.54cm) thick. Fits Remington 740, 742, 750 & 7400.

Mer...

Flere runder enn fabrikkmagasin All-Steel Body gir stivhet

SPECS: stål, blått. Omtrent 31⁄2 "(9 cm) bred, 37⁄16" (8,7 cm) høy, 1 "(2,54 cm) tykk. Passer til Remington 740, 742, 750 & 7400.

Mer...

Kundevurderinger for Triple-K REMINGTON 7400/742 MAGAZINE 30-06 SPRINGFIELD 10RD STEEL BLA

Antall vurderinger: 16
Fra brownells.com: 16
Gjennomsnittsvurdering: 2,9

does the job (21.04.2010)

bought for my rem750 in .270 win. ammo loads well, mag fits like a dream and no problems with jams, ftf, etc up to this point.
numbers don't lie, 10>4, hope to be using these for a while

Awesome Purchase (22.06.2010)

Works well in 7600 (10.07.2010)

979M REM 7400 10rd magazine (28.05.2011)

I was glad of purchase I made from Italy, so that my friends who have also a Remington 7400 luxury carbine .30-06 I prayed for them to buy the magazine from 10 shots.

Not perfect. (12.09.2011)

Triple K Version is generally good (27.11.2011)

not again (19.01.2012)

bought 2 for 742 30-06, fowler poped out, no front tabs to hold fowler in, sides misscut,
sides not bent in at a proper curve to hold rounds, not worth the postage to return to triple k

Good buy. (29.06.2012)

Good buy. ran 50 rounds through it in one session, no misfeeds, worked like a champ.

will not chamber 3 rounds in a row. (03.10.2012)

Poor Quality Magazines (16.09.2014)

7400 rifle (11.11.2014)

Very reliable (11.02.2016)

Doesn't worn in Model 742 (28.07.2016)

Trash (01.03.2018)

Puts bullets in my gun (09.03.2018)

Not bad but needs improvement (12.08.2018)

Les 16 flere anmeldelser fra brownells.com

Kunder kjøpte også

EGW REMINGTON 4, 6, 7400, 750, 7600, 7615 0 MOA
REMINGTON 4, 6, 7400 HD SCOPE BASES

EGW

På lager Leveringstid ca. 14-21 dager.
1 stk. på lageret i USA

kr 999,00 *

Baser til rifler

LITTLE CROW GUNWORKS, LLC. 17 REMINGTON FIREBALL TRIM CHAMBER
WFT 2 TRIMMER

LITTLE CROW GUNWORKS, LLC.

På lager Leveringstid ca. 14-21 dager.
1 stk. på lageret i USA

kr 499,00 * kr 499,00 - kr 1 349,00*

Hylstrimmere

4,3

BROWNELLS OILER BOTTLES 1OZ 3 PACK
NEEDLE OILER BOTTLES

BROWNELLS

På lager Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

kr 379,00 *

Spruteflasker

Harris SLING SWIVEL M14/M1A BIPOD ADAPTER
SLING SWIVEL M14/M1A BIPOD ADAPTER

Harris

Kommer til lager Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

kr 279,00 *

Tilbehør til tofot

NORDIC COMPONENTS MAGAZINE EXTENSION CLAMP
MAGAZINE EXTENSION SUPPORT CLAMP

NORDIC COMPONENTS

På lager Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

kr 799,00 *

Utstyrsmontasje

4,6

Logg inn

Glemt passord?
Registrere

CONNECT

NETTSTEDSKART

PRODUKTKATEGORIER

BESTILLING

KUNDE SERVICE

Velkommen!

Velkommen til Brownells.no, Norges ledende leverandør av våpenrelaterte produkter, våpendeler, børsemakerverktøy, ladeverktøy, ladeutstyr og ladekomponenter!

Vårt kundeløfte:

Uansett om du bare liker å skyte, har våpen som hobby, er børsemaker og reparerer våpen daglig eller bare eier et våpen er dette siden for deg! I over 75 år har skyttere, profesjonelle børsemakere, hobby utøvere, militæret, politiet og våpenreparatører kommet til Brownells for å finne produkter og deler av høy kvalitet. Hos oss finner du over 40 000 produkter inkludert unike våpendeler, tilbehør, børsemakerverktøy, ladeverktøy, ladeutstyr, komponenter, ammunisjon og andre produkter for å vedlikeholde, reparere eller oppgradere dine våpen.