The KIDD aftermarket replacement for the .22LR Fluted Stainless Steel Bull Barrel is one of the best-looking barrels on the market and performs with the expected KIDD Quality. The fluting enhancement in a .22 rimfire is more of an aesthetic or cosmetic feature rather than for cooling purposes. But this refined barrel doesn't just look good it is also guaranteed to group 1/2" at 50 yards. This bull barrel will slip into your factory 10/22 receiver or other aftermarket 10/22 receiver. KIDD believes these are the finest barrels on the market, each one is hand lapped. Their stainless-steel barrel is bored and rifled by Lothar Walther in Germany. Tony Kidd then performs all the final machining to make their match barrel a worthy KIDD product. A proprietary chamber reamer is used to ensure the cartridge and bullet feed smoothly. KIDD barrels are chambered to accept .22 LR ammo and have a 1:16 twist. Their muzzle threading is 1/2"x28 and is available with a protective cap. FEATURES: Aftermarket 10/22 FLUTED BULL barrel Slip-fit design STAINLESS STEEL HAND LAPPED individually 11 degree crown, 1:16 twist, convex extractor slot Muzzle threading available 1/2"" - 28 1/2"" at 50 yards 5 shot group guarantee Barrel installation: Depending on your receiver, if there is paint build up in the receiver mortise be sure to scrape that out. KIDD recommends using an anti-seize compound to assist in installation. Anti-seize is readily available at automotive stores. It is best if you can get the barrel tenon started into the receiver mortise, then turn it over and tap the back of the receiver with a rubber mallet. Be sure to line the extractor slot up as you are installing the barrel. Your barrel is ready to shoot, just run two magazines through it before you really start looking at group size. Do this each time you change brands of ammunition as well. Keep the chamber clean, but don't clean the bore too much you will decrease accuracy. Depending on the ammo, clean the bore around every 500 rounds. Barrel Weights: 20"" SS Fluted barrel = 3 pounds 1 ounce
Oppgrader din Ruger 10/22 med KIDDs matchflutede stålpipe!
KIDDs ettermarkeds erstatning for .22LR Fluted Stainless Steel Bull Barrel er en av de mest attraktive pipene på markedet og leverer den kvaliteten man forventer fra KIDD. Flutingen er mer en estetisk forbedring enn en kjøleeffekt, men denne raffinerte pipen ser ikke bare bra ut; den er også garantert å gruppere 1/2" på 50 yards.
Produktfunksjoner:
- Ettermarkeds 10/22 FLUTED BULL pipe
- Slip-fit design
- STAINLESS STEEL
- HÅNDLAPPEDE individuelt
- 11 graders krone, 1:16 twist, konkav utløseråpning
- Muzzle threading tilgjengelig 1/2" - 28
- 1/2" på 50 yards 5 skudd gruppe garanti
Montering av pipen: Avhengig av din receiver, hvis det er malingoppbygnings i mottaket, må du være sikker på å skrape det ut. KIDD anbefaler å bruke et anti-seize middel for å hjelpe med installasjonen. Anti-seize er lett tilgjengelig i bilbutikker. Det er best å få pipens tenon startet inn i mottaket, deretter snu det over og tappe baksiden av mottaket med en gummihammer. Sørg for å justere utløseråpningen mens du installerer pipen. Din pipe er klar til å skyte, bare kjør to magasiner gjennom den før du virkelig begynner å se på gruppestørrelse. Gjør dette hver gang du bytter ammunisjonsmerker også. Hold kammeret rent, men ikke rengjør løpet for mye, da vil du redusere nøyaktigheten. Avhengig av ammunisjonen, rengjør løpet omtrent hver 500 runder.
Pipevekter:
20" SS Fluted pipe = 3 pounds 1 ounce
Hjelp og kontakt
Nyhetsbrev
Klassisk visning
Mobilvisning