CLYMER HEADSPACE GAUGES - GO

300 WSM Go Gauge

Auto-oversatt beskrivelse (Beskrivelse - Produsent): Den eneste måten å måle og teste lengden på kammeret til riflen nøyaktig. Viktig når du kammerer et nytt fat for å sikre et tett, nøyaktig, sikkert kammer. Mer...

Produktnr.: 184100263 184100263

Absolutely Essential For Accurate, Safe, Chamber Work

The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.

SPECS: Machined Steel. Size varies with caliber and gauge style. NOTE: Gauges Interchangeable between calibers have same Stock #. .30/30 Cartridges are .219 Wasp, .219 Zipper, .22 Sav HP, .30-30, .32 Win Spl, .32-40, .375 Win and .38-55. .30/06 Cartridges are .25-06, 6.5mm-06, .270 Win, .30-06, 8mm-06, .338-06 and .35 Whelen. Magnum Cartridges are .257 Weatherby, .264 Win, 6.5 Rem Mag, .270 Weatherby, .275 H&H, 7mm Rem Mag, 7mm Weatherby, 7x61 S&H, .300 H&H, .300 Win Mag, .30-338, .300 Weatherby, .308 Norma, 8mm Mag, .338 Win, .340 Weatherby, .350 Rem Mag, .357 Norma, .375 H&H, .416 Rem Mag and .458 Win.

Mer...

Helt essensielt for nøyaktig, sikkert, kammerarbeid

Den eneste måten å måle og teste lengden på kammeret til riflen nøyaktig. Viktig når du kammerer et nytt fat for å sikre et tett, nøyaktig, sikkert kammer. Når du kjøper en brukt pistol, må du alltid sjekke headrommet før du skyter. Målere er etset med “Go” eller “No-Go” og navn på kaliber / måler for enkel identifisering. Både Forster og Clymer målere er laget av SAAMI spesifikasjoner.

SPECS: maskinert stål. Størrelsen varierer med kaliber og måler stil. MERKNAD: Målere som kan byttes mellom kaliber har samme varenr. .30 / 30 patroner er .219 Wasp, .219 Zipper, .22 Sav HP, .30-30, .32 Win Spl, .32-40, .375 Win og .38-55. .30 / 06-kassetter er .25-06, 6.5mm-06, .270 Win, .30-06, 8mm-06, .338-06 og .35 Whelen. Magnum kassetter er .257 Weatherby, .264 Win, 6.5 Rem Mag, .270 Weatherby, .275 H&H, 7mm Rem Mag, 7mm Weatherby, 7x61 S&H, .300 H&H, .300 Win Mag, .30-338, .300 Weatherby , .308 Norma, 8mm Mag, .338 Win, .340 Weatherby, .350 Rem Mag, .357 Norma, .375 H&H, .416 Rem Mag og .458 Win.

Mer...

Kundevurderinger for 300 WSM Go Gauge

Antall vurderinger: 6
Fra brownells.com: 6
Gjennomsnittsvurdering: 3,5

Gauge Identification (03.03.2016)

Gauge identification is not the best. Barely readable. Clymer should engrave the identification what the tool is into the body or head. These are my first and only set of headspace gauges. So I will know that they are 5.56. But to make sure not to confuse them. I will get some red and green paint and paint the ring in front of the head. Green for go gauge, Red for no-go gauge. I did not mic them yet. The identification ink is the only problem I've seen.

Hard to read identification on tool (06.03.2016)

Identification should be engraved on tool. Ink is too light. I bought a go gauge and a no-go gauge. The ink on both tools is hard to read. Neither came with any instructions

Great tool for checking headspace (07.03.2016)

I am new into building AR-15's. They are very easy to build and are like adult Lego's for me. It was suggested that I have an extra bolt carrier as a spare if you shoot a lot. So I assembled my bolt carrier with the Adam Arms Piston Bolt carrier and I used the BCM Bolt. To be safe and be certain there would be no bolt/bolt carrier failure, I wanted to make sure my head space was correct. I bought the Brownells Bolt Extractor tool (read review) and used the Go/No-Go units. They worked flawlessly. It took less than 30 seconds for each procedure. I know I can use the spare with no issues and not have to worry about head space. This is a must tool for peace of mind!

Safety First (09.03.2017)

I purchase this Gauge after trying to locate a gunsmith near where I lived and worked to check the head space on my AR build. It was cheaper than a 2-3 hour drive and it work as it was designed.

No Problems (30.03.2017)

works as advertized.

Good product, no extractor cutout. (09.07.2010)

I have to give it a good review because it's my fault. The extractor on my mosin nagant 91/30 absolutely won't budge. The go works fine but the no go obviously won't seat correctly without the removal of the extractor. Both (go and no go) look like fine tools but I can't rate them so much as I can say you DON'T have to remove the firing pin you DO have to remove the extractor so make sure you can do that before ordering them.

Les 6 flere anmeldelser fra brownells.com

528 894 38 NOK

184100263
300 WSM Go Gauge
Produsentnr.: GO300WSM Den eneste måten å måle og teste lengden på kammeret til riflen nøyaktig. Viktig når du kammerer et nytt fat for å sikre et tett, nøyaktig, sikkert kammer. Når du kjøper en brukt pistol, må du alltid sjekke headrommet før du skyter. Målere er etset med “Go” eller “No-Go” og navn på kaliber / måler for enkel identifisering. Både Forster og Clymer målere er laget av SAAMI spesifikasjoner.

821 NOK 11 kr 821,00 *

10+ på lager

Spesifikasjoner: Cartridge: 300 WSM (Winchester Short Mag), 270 WSM (Winchester Short Mag), 338 Winchester Magnum, 325 WSM (Winchester Short Mag) Style: Go Gauge

CLYMER HEADSPACE GAUGES - GO

300 WSM Go Gauge

Kundevurderinger for 300 WSM Go Gauge

Attributes

Elementdetaljer

Kundevurderinger for 300 WSM Go Gauge