OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) is the latest member of the OPF line. G43x and 48 MOS slides are designed for direct mounting of the Shield RMSc sight. Trijicon's RMRcc is longer, and requires an adapter plate which also necessarily raises the mounting surface in order to mount an RMRcc. RMRcc has its own footprint. Gone are the two lug holes in front, these are replaced by two larger diameter threaded posts (bosses) through which the sight to mount/plate screws are installed. The sight to mount/plate screws are also significantly strengthened, though with the OPF-G, RMRcc design that holds the sight immobile on the plate, the larger diameter and stronger screws aren't as important, we always welcome screws that are less likely to strip. With the OPF-G43x/48, RMRcc, we didn't merely raise the mounting surface to provide a platform for the RMRcc. As RMRcc is longer than the G43X/48 MOS cut, the sight overhangs on the slide. When installed, the bottom of RMRcc (with Trijicon provided sealing plate installed) is almost flush with the top of the slide so the sight is as low as possible. We positioned the RMRcc towards the center of the plate as much as feasible, this is done to reduce the amount of unsupported overhang on the RMRcc's sealing plate in front. RMRcc has a rubber gasket around its battery compartment to keep water and moisture at bay, which pushes the sealing plate downward. This isn't an issue if the plate is of the same length as the RMRcc, but with an overhang, it creates a slight gap between the gasket and the sealing plate. OPF-G43x/48, RMRcc's design eliminates the gap/opening between the sight and sealer plate, to the point of emulating a plate that's as long as the sight itself. To wit, if the plate is as long as the RMRcc, it will make the installed height of RMRcc even taller, which is the very reason we chose to let the sight overhang. Torque value: Plate to slide: 12 to15 in·lbs. Sight to plate: 18 in·lbs.. Weight: 0.75oz Material: 1018 steel, black nitrided
Adapterplaten for Trijicon RMRcc til Glock 43/48 er her!
OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) er det nyeste medlemmet av OPF-linjen. G43x og 48 MOS-skyteme er designet for direkte montering av Shield RMSc sikte. Trijicons RMRcc er lengre og krever en adapterplate som også nødvendigvis hever monteringsflaten for å montere et RMRcc.
Spesifikasjoner
RMRcc har sin egen fotavtrykk. De to festepunktene foran er nå erstattet av to større gjengede pinner (boss) gjennom hvilke sikte-til-monteringsplate skruene er installert. Skruene er også betydelig forsterket, selv om designet til OPF-G, RMRcc holder sikte immobile på platen, er de større og sterkere skruene ikke like viktige. Vi setter alltid pris på skruer som er mindre sannsynlige for å strippe.
Montering og design
Med OPF-G43x/48, RMRcc har vi ikke bare hevet monteringsflaten for å gi en plattform for RMRcc. Siden RMRcc er lengre enn G43X/48 MOS-kuttet, stikker sikte ut over skytemet. Når det er installert, er bunnen av RMRcc (med Trijicon levert tetningsplate installert) nesten i flukt med toppen av skytemet, slik at sikte er så lavt som mulig.
- RMRcc er plassert så nær midten av platen som mulig for å redusere mengden usupportert overheng på RMRcc's tetningsplate foran.
- RMRcc har en gummitetning rundt batterirommet for å holde vann og fuktighet unna, noe som presser tetningsplaten nedover.
- Dersom platen er av samme lengde som RMRcc, vil det skape en liten åpning mellom tetningen og tetningsplaten.
OPF-G43x/48, RMRcc's design eliminerer gapet/åpningen mellom sikte og tetningsplate, til det punktet at det etterligner en plate som er like lang som sikte selv. For å være presis, hvis platen er like lang som RMRcc, vil den gjøre den installerte høyden til RMRcc enda høyere, noe som er grunnen til at vi valgte å la sikte stikke ut.
Tekniske detaljer
- Momentverdi: Plate til skytemet: 12 til 15 in·lbs.
- Sikte til plate: 18 in·lbs.
- Vekt: 0.75 oz
- Materiale: 1018 stål, svart nitridert