Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge

EGW
RUGER AUTO VORTEX VIPER/VENOM SIGHT MOUNT

841370112951 296000668
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
999 999 1 NOK
Produktnr.: 296000668
EGW RUGER AUTO VORTEX VIPER/VENOM SIGHT MOUNT
Produsentnr.: 49321 841370112951 EGW rødpunktsikter er ment å installeres fra venstre mot høyre (med munningen vendt fremover). Sporet har en progressiv avsmalning for å tillate enklere installasjon. Bare fjern baksiktet på våpenet ditt og erstatt det med EGW-festet for å montere ditt Vortex Viper/Venom, Burris FastFire eller Docter rødpunktsikte. Du kan når som helst ta av festet og erstatte baksiktet. Monteringsutstyr inkludert. Installasjonsinstruksjoner Fjern baksiktet* Installer EGW Sight Mount i sporet Stram sett-skruen (hvis aktuelt) Plasser rødpunktsiktet på EGW Sight Mount (det å plassere et lite papirstykke mellom rødpunktsiktet og siktefestet vil gjøre fjerning enklere og vil holde Loctite borte fra rødpunktsiktet.) Påfør blå Loctite på de medfølgende monteringsskruene Trekk til monteringsskruene med 15in/lbs 2 knappehodekapselskruer - Levert for Vortex Viper og Venom sikter 2 flatkapselskruer - Levert for Burris FastFire og Docter sikter Skruene som følger med dette festet krever en 5/64'' unbrakonøkkel for installasjon. Modifisering av våpenet ditt kan oppheve produsentens garanti. Dette produktet bør installeres og sjekkes av en kvalifisert børsemaker. Ingen ansvar uttrykkes eller antydes for skade eller skader som kan oppstå som følge av feil installasjon eller bruk av dette produktet.
999 NOK 4 kr 999,00 *
Leveringstid ca. 14-21 dager.
4 stk. på lageret i USA
Spesifikasjoner: Farge: Black Make: Ruger Material: Aluminum Modell: Mark III, Mark I, Mark II, P90, P93, P94, P95, P97, P89, 22/45, P85, P91, Mark IV Number of Bases: 1-Piece Style: Tactical

Attributes

Farge: Black Make: Ruger Material: Aluminum Modell: Mark II,P93,P97,22/45,Mark I,P89,Mark III,P91,P90,P94,P95,P85,Mark IV Number of Bases: 1-Piece Style: Tactical Leveringsvekt: 0,045kg Frakthøyde: 25mm Fraktbredde: 76mm Fraktlengde: 140mm

Elementdetaljer

Made in USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Nyhetsbrev