Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge
080000409
Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

1849 1849 1 NOK
Produktnr.: 080000409
BROWNELLS FIRING PIN REMOVAL TOOL Et tredje hånd for å fjerne tennstiften fra Remington og Ruger® boltrifler uten tapte deler eller såre fingre som noen ganger følger med denne vanskelige jobben. Installer den riktige bøssingen for din rifle i enden av verktøykroppen. Skru tennstiftsamlingen inn i bøssingen, og stram den gjengede stålskaften for å komprimere og fange hovedfjæren. Den hule skaften beskytter tennstiftspissen når den glir over stift for å komprimere fjæren. Krysspinnen kan deretter drives ut med en punsj, og fjærspenningen kan lettels av gradvis løsning av skaften. Inkluderer bøssinger for Remington 700 familien og Ruger M77® Mark II rifler. Innebygd lagringsplass holder den ubrukte bøssingen på verktøykroppen, slik at den alltid er der når du trenger den. MERK: Vil ikke passe til Ruger venstrehendte handlinger.
1849 NOK 0 kr 1 849,00 *
Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.
Spesifikasjoner: Make: Ruger, Remington Modell: Universal Rifles

Attributes

Make: Remington,Ruger Modell: Universal Rifles Leveringsvekt: 0,431kg Frakthøyde: 58mm Fraktbredde: 112mm Fraktlengde: 183mm

Elementdetaljer

Made in USA



Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

Nyhetsbrev