Din handlekurv er tom.

Handlekurv

37 17 00 00

Meld på nyhetsbrev

VOLQUARTSEN
EXACT EDGE EXTRACTOR MKII, MKIII, MKIV, 10/22®

810162010546 930000010

Tuned & Hardened For Lasting Performance

Machined with exacting tolerances; hook is .005" closer to rim to give a positive, non-slip grip on the case head. The very precise hook point is hardened to Rc 58-60, will not lose its edge, even after years of use.

SPECS: A-2 tool steel, in-the-white. Fits Ruger MKII, MKIII, MKIV and 22/45 pistols; 10/22 and 10/22 magnum.

Mer...

Tunet og herdet for varig ytelse

Maskinert med nøyaktige toleranser; kroken er 0,005 "nærmere kanten for å gi et positivt, sklisikkert grep på kabinhodet. Det veldig presise krokpunktet er herdet til Rc 58-60, vil ikke miste kanten, selv etter mange års bruk.

SPECS: A-2 verktøystål, hvitt. Inkluderer utskiftningsfjær. Passer Ruger MKII, MKIII, MKIV og 22/45 pistoler; 10/22 og 10/22 magnum.

Mer...

Kundevurderinger for VOLQUARTSEN EXACT EDGE EXTRACTOR

Antall vurderinger: 13
Fra brownells.com: 12
Gjennomsnittsvurdering: 5

Works GREAT in Ruger auto pistols too ! (25.10.2009)

These extractors work GERAT in my Ruger Mk II and Mk III 22 autos. Use the extractor only - must use the original factory extractor spring. Work so well that I have replaced the extractors in all six of my pistols. Any extraction problem will just disappear.

Volquartsen Is Good Medicine! (24.08.2010)

It seems like the newer Ruger 10/22 extractors are made from soft metal and the edges dull quickly. After 2000 rounds or so, jams can become problematic--even with ammo that was jam-free when the rifle was new. The Exact Edge Extractor is the fix!

No more stuck shells. (22.01.2012)

This was easy to install and after testing it I have yet to have another failure to extract.

Extractor (10.02.2013)

A lot sharper and more surface area over the Factory Ruger extractor. More consistent ejection and jams are now non existent.

Broken to improved with one little part (15.03.2013)

I didn't get this to improve my 10/22, i bought it because my old extractor flew out of my rifle during a plinking spree. I just assumed that Ruger 1022's just failed to eject periodically due to ammo or low grade systems or that I ran about 5,000 rounds through it over 20 some years with only barrel cleaning and wiping lubrication only of the visible assembled carriage system. What a difference. This thing grabs the rim firmly and squarely and under close examination, the precise and sharp, greater than 90 degree tooth plants it's pointed tooth perfectly and aggressively into the base of the chambered round's rim and pulls it cleanly out like a wolf ripping flesh. The Volquartsen spring, although shorter has far more force than the original spring creating a more sure and precise "bite". Closing the bolt slowly, you can hear the extractor snapping in place. Such a small part but what a major improvement. Not a single failure yet. I'm glad my original piece broke so, with the help of YouTube, I could fully disassemble the rifle and do a full de-grease and re-lube with Slip2000 and some TW25b weapon grease then upgrade a small but very important and quality part to revive my enjoyment of this classic piece that will soon belong to my son. Now I brought new life into a favorite toy!

THIS IS THE FIX (18.02.2014)

This extractor is very quality made. It is easy to see if you lay it next to the stock unit there is no comparison. They are similar but there is a big difference, anyway it fixed my 10/22 made it better than new went from 3 or more jams/stovepipes per 10 clip to zero jams due to faulty extractor hold. Also a big thank you to Brownell's for quick proccess and shipping, I got it in four days from time ordered. Thanks to Volquartsen for a quality made product.

Easy Install & Works Great (12.04.2014)

I installed the extractor in a Mk2. It took about 20 minutes from start to finish. Then I took the gun to the range and had ZERO FTE's. Before I was having 3 or more FTE per magazine. Extremely satisfied with the VQ Extractor.

Perfect (13.07.2015)

Seriously perfect. I would have anywhere from 1-4 FTE's per 10 clip before. I went shooting, and put 300 rounds of varying brands through it, and had 0 FTE's. If there was only one mod I could do to a 10/22, it would be this.

The spring that came with the extractor was too short though, so I just used the stock one.

Could be A MIRACLE! (25.10.2015)

I had my doubts about this VQ Extractor putting an end to the FTE's all too frequently in our 10/22 Takedown. We purchased the rifle in early March and we've encountered this problem at least once at almost every single session at the range since then. (Other than this frustrating characteristic, the rifle has become an inanimate member of the family; we do like it.)

Cleaning helped at times, but was apparently not THE solution. So, we got pretty good at clearing jams.

However, as the factory extractor showed more and more wear-and-tear, including the claw rounding off. (Image attached, in case it is happening to you.) I knew I'd have to do something. Then, during a session in early October, I not only had a spike in FTE's, I twice had chambered rounds that would not extract when I manually racked the bolt; it was time to do something.

I initially planned to just buy a couple factory extractors but, having read so much good about the VQ extractor, I bought one of each. Last weekend, I replaced the original "rounder" with the VQ. Yesterday, I was able to test it. IT'S A MIRACLE! Okay, it was one session, but I sent 210rds of mixed makes & types of ammo, including some that were physically/mechanically "questionable", and I had 0, zero, nil, nada, FTE's.

Very, very cool.

<img width="500" src='/userdocs/reviewimages/04fbcc6b-2169-43bd-a99f-f5161dde82cf.jpg' alt=''>

PERFECT (25.06.2016)

My 10/22 would FTE at least once per mag. Read all the good previous reviews. Ordered additional for my MKIII. Compared the extractor lip of the VQ to the factory extractor on both guns. Increase in quality, purchase on rim and strength of spring was more than quite obvious. Note: The provided spring is shorter than factory but STRONGER. "NO MORE FTE's !"

Flawless (21.04.2017)

This simple upgrade made all of the difference. I recently upgraded the stock barrel and after making the switch I experienced numerous FTEs. Before trying more extreme options I tried this simple upgrade. Turns out this $12 part was all I neede. Just put a few hundred rounds through it without a single issue. Nothing gets past this claw!

No Malfunctions During Last Outing! (17.07.2018)

After receiving a Ruger Mark III Target for a gift in 2009 I left it stock for nearly a decade. It has accounted for a few different species of animals as well as paper and steel targets. During the past few years there seemed to be an increase in the number of malfunctions - failures to extract or eject the brass. After ordering and receiving the Volquartsen Exact Edge Extractor I installed it myself with a referral to some of the online videos detailing the steps. It is a little more time consuming getting the old extractor out than getting the Volquartsen extractor in but not too bad. I followed the instructions on the box which suggested using the Ruger extractor spring when installing the Volquartsen extractor on the Mark series pistols. My first outing to fire the Mark III after the Volquartsen extractor install was a brief 100 rounds in fairly rapid succession. I fired 50 rounds of CCI MiniMags and 50 rounds of low cost Federal ammunition (the modern equivalent of the old Federal Lightning). The pistol had no malfunctions of any kind! It has been a long time since that happened. I firmly believe this Volquartsen Exact Edge Extractor has vastly improved the reliability of this pistol.

Bedre enn original (11.01.2017)

Denne er mye mer polert enn original, skarpere i kantene og gir meg hvertfall mye bedre inntrykk av kvalitet.
Den originale er full av små grader og sår, som får meg til å miste litt tillit.

Denne skal også være av sterkere stål og ha lenger levetid i følge produsenten. Kun brukt noen uker så vanskelig å si noe om levetiden.
Synes også den beveger seg smidigere i slutstykket.
Føler hvertfall at den er av betydelig bedre kvalitet enn original, og da stoler jeg mer på den :)

Les 12 flere anmeldelser fra brownells.com

319 319 1 NOK

Produktnr.: 930000010
VOLQUARTSEN EXACT EDGE EXTRACTOR
Produsentnr.: VC10EE 810162010546 Maskinert med nøyaktige toleranser; kroken er 0,005 "nærmere kanten for å gi et positivt, sklisikkert grep på kabinhodet. Det veldig presise krokpunktet er herdet til Rc 58-60, vil ikke miste kanten, selv etter mange års bruk.

319 NOK 35 kr 319,00 *

Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

Spesifikasjoner: Make: Ruger Modell: Mark III, Mark II, 10/22, 10/22 Magnum, Mark IV

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Attributes

Make: Ruger Modell: 10/22,Mark II,Mark III,Mark IV,10/22 Magnum Leveringsvekt: 0,005kg Høyde: 10mm Bredde: 71mm Lengde: 89mm

Elementdetaljer

Made in USA
US eksport klassifisering: 0A501.x

Tuned & Hardened For Lasting Performance

SPECS: A-2 tool steel, in-the-white. Fits Ruger MKII, MKIII, MKIV and 22/45 pistols; 10/22 and 10/22 magnum.

Mer...

Tunet og herdet for varig ytelse

SPECS: A-2 verktøystål, hvitt. Inkluderer utskiftningsfjær. Passer Ruger MKII, MKIII, MKIV og 22/45 pistoler; 10/22 og 10/22 magnum.

Mer...

Kundevurderinger for VOLQUARTSEN EXACT EDGE EXTRACTOR

Antall vurderinger: 13
Fra brownells.com: 12
Gjennomsnittsvurdering: 5

Works GREAT in Ruger auto pistols too ! (25.10.2009)

Volquartsen Is Good Medicine! (24.08.2010)

No more stuck shells. (22.01.2012)

This was easy to install and after testing it I have yet to have another failure to extract.

Extractor (10.02.2013)

A lot sharper and more surface area over the Factory Ruger extractor. More consistent ejection and jams are now non existent.

Broken to improved with one little part (15.03.2013)

THIS IS THE FIX (18.02.2014)

Easy Install & Works Great (12.04.2014)

Perfect (13.07.2015)

Could be A MIRACLE! (25.10.2015)

PERFECT (25.06.2016)

Flawless (21.04.2017)

No Malfunctions During Last Outing! (17.07.2018)

Bedre enn original (11.01.2017)

Les 12 flere anmeldelser fra brownells.com

Kunder kjøpte også
Alternativer

VOLQUARTSEN BLUE 10/22® BOLT RELEASE
RUGER® 10/22® BOLT RELEASE

VOLQUARTSEN

Kommer til lager Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

kr 299,00 *

4,6

VOLQUARTSEN EXTENDED BOLT HANDLE
RUGER® 10/22® EXTENDED BOLT HANDLE

VOLQUARTSEN

Kommer til lager Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

kr 1 049,00 *

Charging Handles

4,3

Tuffer Buffer BOLT BUFFER, 3-PAK
RUGER® 10/22® BOLT BUFFER

Tuffer Buffer

På lager Leveringstid ca. 14-21 dager.
2 stk. på lageret i USA

kr 459,00 * kr 219,00 - kr 459,00*

4,4

VOLQUARTSEN RECOIL BUFFER PIN
10/22® RECOIL BUFFER PIN

VOLQUARTSEN

Kommer til lager Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

kr 299,00 *

Låskasse pinner

VOLQUARTSEN 10/22® DROP-IN HAMMER
10/22® DROP-IN HAMMER

VOLQUARTSEN

Kommer til lager Restordre. Sendes når kommer til lager. Leveringstid ca 4-12 uker fra USA lager.

kr 949,00 *

Hammere

4,8

Logg inn

Glemt passord?
Registrere

CONNECT

NETTSTEDSKART

PRODUKTKATEGORIER

BESTILLING

KUNDE SERVICE

Velkommen!

Velkommen til Brownells.no, Norges ledende leverandør av våpenrelaterte produkter, våpendeler, børsemakerverktøy, ladeverktøy, ladeutstyr og ladekomponenter!

Vårt kundeløfte:

Uansett om du bare liker å skyte, har våpen som hobby, er børsemaker og reparerer våpen daglig eller bare eier et våpen er dette siden for deg! I over 75 år har skyttere, profesjonelle børsemakere, hobby utøvere, militæret, politiet og våpenreparatører kommet til Brownells for å finne produkter og deler av høy kvalitet. Hos oss finner du over 40 000 produkter inkludert unike våpendeler, tilbehør, børsemakerverktøy, ladeverktøy, ladeutstyr, komponenter, ammunisjon og andre produkter for å vedlikeholde, reparere eller oppgradere dine våpen.