Din handlekurv er tom.

Handlekurv

37 17 00 00

Meld på nyhetsbrev

BOONIE PACKER PRODUCTS
AR-15/M16 IMPROVED REDI-MAG

100004455

Holds Spare Magazine On The Receiver For Ultra-Fast Reloads

Don’t lose precious seconds in competition or combat fumbling for a spare magazine during a reload. This rugged speed loading system clamps directly to the lower receiver of any AR-15/M16 rifle or carbine and securely holds a second, fully loaded magazine alongside the mag well for super-fast mag changes. More reliable and easier to use than improvised methods, like taping two magazines together, that can cause malfunctions at critical moments. Closed-top design protects the spare mag from rain, dirt, dust, and debris and prevents the top round from jumping forward under recoil. Independent release system lets you drop the spare mag and the mag in the weapon separately to allow tactical reloads and greater flexibility in clearing malfunctions. Bolt Catch Extension (BCE) mounts directly to the factory bolt catch and lets you release the bolt, with or without the Redi-Mag attached to the gun, simply by slapping the BCE with an open palm. Installation requires no permanent alterations to receiver or mag well. Designed for mil-spec receivers; may not fit custom billet receivers. Steel model available in Standard configuration model that enables faster installation and removal of the entire Redi-Mag from the weapon.

SPECS: Steel, Parkerized, or 6061 T6 aluminum, hardcoat anodized, both dark gray, with reinforced molded polymer BCE and spacer. 3½" (8.9cm) long, 2½" (6.4cm) wide, 2¾" (7cm) high. Weight: 8.4 oz. (234g) (steel), 5.6 oz. (159 g) (aluminum). Fits AR-15/M16/M4 rifles and carbines with standard forged lower receiver.

Mer...

Holder Et Ekstra Magasin På Mottakeren For Lynraske Omladninger

Mist ikke verdifulle sekunder i konkurranse eller kamp ved å famle etter et ekstra magasin under omlading. Dette robuste hurtigladningssystemet klemmes direkte på den nedre mottakeren til enhver AR-15/M16 rifle eller karabin og holder sikkert et andre, fulladet magasin ved siden av magasinbrønnen for superraske magasinbytter. Mer pålitelig og enklere å bruke enn improviserte metoder, som å tape to magasiner sammen, som kan forårsake funksjonsfeil i kritiske øyeblikk. Lukket toppdesign beskytter det ekstra magasinet mot regn, smuss, støv og rusk og forhindrer at den øverste patronen hopper frem under rekyl. Uavhengig utløsersystem lar deg slippe det ekstra magasinet og magasinet i våpenet separat for å tillate taktiske omladninger og større fleksibilitet ved å rydde funksjonsfeil. Bolt Catch Extension (BCE) monteres direkte på fabrikkens boltfanger og lar deg slippe bolten, med eller uten Redi-Mag festet til våpenet, bare ved å slå BCE med åpen håndflate. Installasjon krever ingen permanente endringer på mottaker eller magasinbrønn. Designet for mil-spec mottakere; passer kanskje ikke tilpassede billettmottakere. Stålmodell tilgjengelig i Standard konfigurasjonsmodell som muliggjør raskere installasjon og fjerning av hele Redi-Mag fra våpenet.

SPECS: Stål, parkerisert, eller 6061 T6 aluminium, hardcoat anodisert, begge i mørkegrått, med forsterket støpt polymer BCE og spacer. 3½" (8.9cm) lang, 2½" (6.4cm) bred, 2¾" (7cm) høy. Vekt: 8.4 oz. (234g) (stål), 5.6 oz. (159 g) (aluminium). Passer AR-15/M16/M4 rifler og karabiner med standard smidd nedre mottaker.

Mer...

Kundevurderinger for BOONIE PACKER PRODUCTS IMPROVED REDI-MAG, STANDARD STEEL

Antall vurderinger: 10
Fra brownells.com: 10
Gjennomsnittsvurdering: 4,1

Solid mount (09.11.2009)

If you want to have a spare mag solidly attached to the weapon this is the way to go.

Unlike pouches or rail mounted mag holders this allows the user to have a spare in a very natural spot.

Perfect for when you are required to be condition 4 but want to have a mag ready to go (LE/Military). Great for 3 gun or carbine matches or anywhere a quick reload is needed.

The bolt release button is a bit small but a solid smack with the heel of your hand to the side of the receiver will send the bolt forward anyway.

Great Product (13.11.2009)

Gives you a spare mag without having to mess with pouches. You're hand doesn't have to leave the rifle for more than a couple of seconds. Does not work well with PMAGs since they only have a small indent.

excellent upgrade for operators (24.12.2009)

THE MOST useful accessory i have added to my carbine.
works well with BAD lever as well
there is nothing quite like picking up my carbine 24/7 with 60 rounds attached to it.

Fast/Tactical reload a must? Get this! (13.06.2011)

This product is GREAT! Hands down. It keeps a fully loaded mag right next to the one in the gun. Just hold the full one, drop the empty and switch 'em. Left handed AR owner? Works just fine for us (yes, I'm one too)though it's not a must, I would recommend the Magpul B.A.D Lever. It works with the Redi-Mag and makes it a lot easier to operate the bold release.

very useful (27.06.2011)

Mine has been in service on my duty rifle for over 10yrs. No problems whatsoever. Would definitley buy again. Some things are "cool". This item is USEFUL.

Best addon since an optic (16.12.2011)

I run the Redimag on my patrol rifle. I am not an AR junkie that adds on every new shinny thing that comes out, I run a sling, optic, and light. I use my rifle as a tool to do my job not to look cool. The Redimag is a needed addon. No other spare mag carrier holds ammo as secure and deploys so rapidly. It's a must have!

A little struggling to put on, but anyone can do it. I wish the rubber gaskets that protect the AR magwell from scratches was one piece instead of three. However once its on, it's secure and greatly increases reloading speed.

installation is a pain (21.06.2012)

This thing was a PITA to install. The screw holes didn't want to line up and my Magpul BAD lever was rubbing so I had to take the Dremel tool to it. After all the hassle getting it on my lower I found it doesn't like LMT MRP uppers. The Redi-Mag hits the area just behind the barrel screws. I was able to get the upper mounted, but its pushing the Redi-Mag out just a enough that the flared floor plates on my Pmags are touching. It doesn't look like it'll be enough to stop a mag from dropping free but time will tell.

Must have for tactical reloads (24.06.2013)

I've had this on my AR15 for well over 10 years and it's the old version. Once you are adapted to it, you will find you are the fastest guy on the line as your backup mag is right with you. Has never failed to drop the mag. Simply grab the reload mag before you punch the mag release and as the empty mag drops free, slide in your backup mag. It does make your gun heavier but doesn't seem to affect the balance. I'm ordering a new aluminum RediMag for a new gun. Works with BAD lever, another must have.

Mag ready (01.09.2017)

I've been thinking of getting this for years. I was concerned the steel would be too heavy. After installing I picked up the ar and realized it wasn't bad at all. Besides once you install a full mag "it's heavy!" Installation was pretty simple. I used a small clamp to hold the screw section together to install the screws though it did come with a screw and nut to do the same thing. The worst part was the nylon nuts. That was a bit of a PITA but with the right tools still hardly an issue. I use 20 rounders for general SD since I'm not in LE. Im also left handed and it worked well for me. A little practice and mag changes were quick and easy. I'll keep practicing to make sure it's second nature. I'm going to install another on my house SBR. HIGHLY RECOMMENDED.

Will not fit commercial lowers (26.11.2017)

This will only fit lowers that have a removable trigger guard. It will not fit lowers that have a molded in trigger guard as many commercial lowers do.

Les 10 flere anmeldelser fra brownells.com

1849 1849 1 NOK

Produktnr.: 100004455
BOONIE PACKER PRODUCTS IMPROVED REDI-MAG, STANDARD STEEL
Produsentnr.: RMMKI Mist ikke verdifulle sekunder i konkurranse eller kamp ved å famle etter et ekstra magasin under omlading. Dette robuste hurtigladningssystemet klemmes direkte på den nedre mottakeren til enhver AR-15/M16 rifle eller karabin og holder sikkert et andre, fulladet magasin ved siden av magasinbrønnen for superraske magasinbytter. Mer pålitelig og enklere å bruke enn improviserte metoder, som å tape to magasiner sammen, som kan forårsake funksjonsfeil i kritiske øyeblikk. Lukket toppdesign beskytter det ekstra magasinet mot regn, smuss, støv og rusk og forhindrer at den øverste patronen hopper frem under rekyl. Uavhengig utløsersystem lar deg slippe det ekstra magasinet og magasinet i våpenet separat for å tillate taktiske omladninger og større fleksibilitet ved å rydde funksjonsfeil. Bolt Catch Extension (BCE) monteres direkte på fabrikkens boltfanger og lar deg slippe bolten, med eller uten Redi-Mag festet til våpenet, bare ved å slå BCE med åpen håndflate. Installasjon krever ingen permanente endringer på mottaker eller magasinbrønn. Designet for mil-spec mottakere; passer kanskje ikke tilpassede billettmottakere. Stålmodell tilgjengelig i Standard konfigurasjonsmodell som muliggjør raskere installasjon og fjerning av hele Redi-Mag fra våpenet.

1849 NOK 36 kr 1 849,00 *

Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

Spesifikasjoner: Farge: Dark Gray Make: AR-15

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Attributes

Farge: Dark Gray Make: AR-15 Leveringsvekt: 0,249kg Frakthøyde: 33mm Fraktbredde: 112mm Fraktlengde: 109mm

Elementdetaljer

Made in USA
US eksport klassifisering: 0A501.x

Holds Spare Magazine On The Receiver For Ultra-Fast Reloads

Mer...

Holder Et Ekstra Magasin På Mottakeren For Lynraske Omladninger

Mer...

Kundevurderinger for BOONIE PACKER PRODUCTS IMPROVED REDI-MAG, STANDARD STEEL

Antall vurderinger: 10
Fra brownells.com: 10
Gjennomsnittsvurdering: 4,1

Solid mount (09.11.2009)

Great Product (13.11.2009)

excellent upgrade for operators (24.12.2009)

THE MOST useful accessory i have added to my carbine.
works well with BAD lever as well
there is nothing quite like picking up my carbine 24/7 with 60 rounds attached to it.

Fast/Tactical reload a must? Get this! (13.06.2011)

very useful (27.06.2011)

Mine has been in service on my duty rifle for over 10yrs. No problems whatsoever. Would definitley buy again. Some things are "cool". This item is USEFUL.

Best addon since an optic (16.12.2011)

installation is a pain (21.06.2012)

Must have for tactical reloads (24.06.2013)

Mag ready (01.09.2017)

Will not fit commercial lowers (26.11.2017)

This will only fit lowers that have a removable trigger guard. It will not fit lowers that have a molded in trigger guard as many commercial lowers do.

Les 10 flere anmeldelser fra brownells.com

Kunder kjøpte også

TROY INDUSTRIES M4 OEM SLING MOUNT, BLACK
AR-15/M16 END PLATE SLING MOUNTS

TROY INDUSTRIES

Kommer til lager

kr 1 049,00 *

Taktisk skytereim montasje

3,7

TROY INDUSTRIES BATTLE RAIL COVER 3-PK PICATINNY POLYMER BLACK 6"
AR-15 PICATINNY BATTLE RAIL COVER 3-PK POLYMER

TROY INDUSTRIES

På lager

kr 469,00 * kr 469,00 - kr 479,00*

Skinne deksel

MAGPUL MOE K2+ GRIP POLYMER BLACK
AR-15 MOE K2+ GRIP

MAGPUL

Kommer til lager

kr 469,00 *

Pistolgrep

MAGPUL FINE COTTON UNFAIR ADVANTAGE T-SHIRT BLACK SMALL
MEN'S FINE COTTON UNFAIR ADVANTAGE T-SHIRTS

MAGPUL

Ikke tilgjengelig

GROVTEC US M-LOK NON-ROTATING FLANGED PUSH BUTTON BASE
M-LOK NON-ROTATING FLANGED PUSH BUTTON BASE

GROVTEC US

På lager

kr 449,00 *

Taktisk skytereim montasje

Logg inn

Glemt passord?
Registrere

CONNECT

NETTSTEDSKART

PRODUKTKATEGORIER

BESTILLING

KUNDE SERVICE

Velkommen!

Velkommen til Brownells.no, Norges ledende leverandør av våpenrelaterte produkter, våpendeler, børsemakerverktøy, ladeverktøy, ladeutstyr og ladekomponenter!

Vårt kundeløfte:

Uansett om du bare liker å skyte, har våpen som hobby, er børsemaker og reparerer våpen daglig eller bare eier et våpen er dette siden for deg! I over 75 år har skyttere, profesjonelle børsemakere, hobby utøvere, militæret, politiet og våpenreparatører kommet til Brownells for å finne produkter og deler av høy kvalitet. Hos oss finner du over 40 000 produkter inkludert unike våpendeler, tilbehør, børsemakerverktøy, ladeverktøy, ladeutstyr, komponenter, ammunisjon og andre produkter for å vedlikeholde, reparere eller oppgradere dine våpen.