Stronger spring prevents "extractor bounce" during rapid semi-auto or full-auto fire. Provides extra force against case rim to give AR-15 rifles and carbines reliable extraction from a dirty chamber; ensures fired case is completely extracted and ejected from gun. Recommended for use with black, carbine, extractor spring insert.
Mer...
Forbedrer utvinning og pålitelighet
Sterkere fjær forhindrer "avtrekkssprett" under hurtig semi-auto eller full-auto brann. Gir ekstra kraft mot kanten for å gi AR-15 rifler og karbiner pålitelig ekstraksjon fra et skittent kammer; sikrer at avfyrt sak blir fullstendig trukket ut og kastet ut fra pistolen. Anbefales for bruk med svart, karbin, avtrekksfjærinnsats.
Mer...
Kundevurderinger for WOLFF AR-15/M16 EXTRACTOR SPRING, 3-PAK
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 5
Perfect for 16(26.11.2012)
If your barrel is 16" long and has a carbine length gas system, you NEED this extractor spring.
16" carbine gas guns are VERY hard on extractor springs since their extraction cycle happens so much faster than any other setup. Cheap springs, if they do work at first, will only typically last a few thousand rounds before they start to get really weak.
This spring is stronger from the git-go, more resistant to heat cycling and stress, and will last much longer than a std spring. You can tell when you install it (I rec some flat-nosed pliers to press the base of the spring into the extractor spring cup...the big end goes into the extractor).
This spring is so strong, I do NOT recommend using a Defender D-ring or an o-ring of any type or color...only the black extractor (black = carbine, blue = rifle) insert is recommended.
This is great insurance when you start shooting NATO pressure ammo from a dirty chamber. It also helps guns run 100% with steel-cased ammo, which has been shown to have a secondary pressure spike before the case shrinks after discharge.
It will work with nearly any AR gas system/barrel setup...but it is PERFECT for 16" barrels with carbine gas systems (7" gas tube).
Extractor Spring3-pac(28.12.2014)
i just read the article below this one and I'm sold makes sence to me.great article.Thanks now I'm stock up in spares...
Produktnr.: 969000032 WOLFF AR-15/M16 EXTRACTOR SPRING, 3-PAK Produsentnr.: 30091 Sterkere fjær forhindrer "avtrekkssprett" under hurtig semi-auto eller full-auto brann. Gir ekstra kraft mot kanten for å gi AR-15 rifler og karbiner pålitelig ekstraksjon fra et skittent kammer; sikrer at avfyrt sak blir fullstendig trukket ut og kastet ut fra pistolen. Anbefales for bruk med svart, karbin, avtrekksfjærinnsats.
239NOK40kr 239,00
*
Leveringstid ca. 14-21 dager. Mer enn 10 stk. på lager i USA
Stronger spring prevents "extractor bounce" during rapid semi-auto or full-auto fire. Provides extra force against case rim to give AR-15 rifles and carbines reliable extraction from a dirty chamber; ensures fired case is completely extracted and ejected from gun. Recommended for use with black, carbine, extractor spring insert.
Mer...
Forbedrer utvinning og pålitelighet
Sterkere fjær forhindrer "avtrekkssprett" under hurtig semi-auto eller full-auto brann. Gir ekstra kraft mot kanten for å gi AR-15 rifler og karbiner pålitelig ekstraksjon fra et skittent kammer; sikrer at avfyrt sak blir fullstendig trukket ut og kastet ut fra pistolen. Anbefales for bruk med svart, karbin, avtrekksfjærinnsats.
Mer...
Kundevurderinger for WOLFF AR-15/M16 EXTRACTOR SPRING, 3-PAK
Antall vurderinger: 2
Fra brownells.com: 2
Gjennomsnittsvurdering: 5
Perfect for 16(26.11.2012)
If your barrel is 16" long and has a carbine length gas system, you NEED this extractor spring.
16" carbine gas guns are VERY hard on extractor springs since their extraction cycle happens so much faster than any other setup. Cheap springs, if they do work at first, will only typically last a few thousand rounds before they start to get really weak.
This spring is stronger from the git-go, more resistant to heat cycling and stress, and will last much longer than a std spring. You can tell when you install it (I rec some flat-nosed pliers to press the base of the spring into the extractor spring cup...the big end goes into the extractor).
This spring is so strong, I do NOT recommend using a Defender D-ring or an o-ring of any type or color...only the black extractor (black = carbine, blue = rifle) insert is recommended.
This is great insurance when you start shooting NATO pressure ammo from a dirty chamber. It also helps guns run 100% with steel-cased ammo, which has been shown to have a secondary pressure spike before the case shrinks after discharge.
It will work with nearly any AR gas system/barrel setup...but it is PERFECT for 16" barrels with carbine gas systems (7" gas tube).
Extractor Spring3-pac(28.12.2014)
i just read the article below this one and I'm sold makes sence to me.great article.Thanks now I'm stock up in spares...