Din handlekurv er tom.

Handlekurv

STRIKE INDUSTRIES
RIFLE AK TO AR BUFFER TUBE ADAPTER

700598350463 100016868

Strike Industries stock adapter allows for the replacement of any standard fixed AK stock to be converted to accept an AR buffer tube assembly. This adapter is easy to install without any modifications to your AK. With no need to permanently alter the stock tang as it fits inside the adapter and tube. This product will take your AK into the twenty first century with the looks and the adjust-ability of a M4. Strike Industries also incorporated QD (quick disconnects) on both sides of the AK stock adapter.

SPECS: Length: 2.5", Weight: 4oz, Material: T6061 Aluminum.

Mer...

Strike Industries kolbeadapter gjør det mulig å erstatte enhver standard fast AK-kolbe for å kunne montere et AR buffer tube-sett. Denne adapteren er enkel å installere uten noen modifikasjoner på din AK. Det er ikke nødvendig å gjøre permanente endringer på kolbetangen, da den passer inne i adapteren og tuben. Dette produktet vil ta din AK inn i det tjueførste århundre med utseendet og justerbarheten til en M4. Strike Industries har også inkludert QD (quick disconnects) på begge sider av AK-kolbeadapteren.

SPECS: Lengde: 2.5", Vekt: 4oz, Materiale: T6061 Aluminium.

Mer...

Kundevurderinger for STRIKE INDUSTRIES AK TO AR BUFFER TUBE ADAPTER BLACK ALUMINUM

Antall vurderinger: 5
Fra brownells.com: 5
Gjennomsnittsvurdering: 3,8

does not fit (29.05.2015)

Sturdy design, but does not even come close to fitting C39V2 rifle from century

Fits Great - FOR STAMPED AK's ONLY! (03.06.2015)

The review below me tried fitting it on a milled AK (C39v2). The Brownells video states it's for STAMPED AK's only. Fit well on my DDI stamped AK.

Worth getting to modify your AK (05.09.2015)

I received the product 3 days before it was schedule to arrive, so my 'hats off' to Brownells for their speed of processing delivery. The part fit into my Warsa 10/63 lower receiver without any problems. It is made of the same strong material used in a lot of today's AR's, and the location for the QD attachments is where I like them to be. With the stock fully collapsed, it is a half inch shorter than the standard AK stock, fully extended it is as long as an A2 stock for those that like the longer length of pull.

The only 2 issue's I did have was; (1) the lack of a proper fitting allen key tool to set the lock screw for the buffer tube and the two mounting screws, (2) I had to use a sanding wheel to grind down the edge of the mounting screw that went under the recoil spring/ locking latch for the dust cover to get it to fit flush with the surface and have everything mount properly back into place on the receiver. Other than those two minor issues, this is a great product for anyone who wants to mount an AR collapsible butt stock to their AK 47/74 rifle's. I would have given it 5 stars instead of 4, if it was not for having to do a little work when I was installing the part.

So far, so good (25.10.2015)

I researched this item and went back and forth between it and the rifle dynamics version. This one is half price and when "chatting" with the Brownell's rep, he said I could return it if didn't work out. Well, I figured that was worth a try. The unit fit well on my Saiga with some minor fitting of the mounting screw (filing). However, there are no directions and there are two pieces that fit inside the adapter that I truly don't know what their purpose is. That said, it fit well and looks good. I put a Magpul MOE stock on the AK. The length of the stock with the adapter is outstanding. Time will tell as to durability, but so far I'm very happy.

Exellent product, but... (16.02.2018)

Excellent adapter, very well made.

The best if you plan on using the iron sights as the tube comes lower then on any other similar adapters.

Only caveat is that requires quite a LOT of fitting to install on Norinco; the receiver of T56 is made of 1.5 mm steel compared to most East Block AKs where the material is 1 mm â so the inner diameter is smaller then on most models.

Also, the Chinese tang is about 6 mm longer then standard, so the holes do not fit (see the pic â after taking it, I ended up filing the rear tang hole so it aligns with the hole on the adapter)

I filed the sides and the "forehead" of the part of the adapter that goes inside the receiver, and filed the rear tang screw hole some â now it fits tight and very solid, even without the adjustment pieces.

<img width="500" src='/userdocs/reviewimages/c70e0c1a-d3be-4dee-9d83-9353443560d7.jpg' alt=''>

Les 5 flere anmeldelser fra brownells.com

799 799 1 NOK

Produktnr.: 100016868
STRIKE INDUSTRIES AK TO AR BUFFER TUBE ADAPTER BLACK ALUMINUM
Produsentnr.: SI-AK-SA 700598350463 Strike Industries kolbeadapter gjør det mulig å erstatte enhver standard fast AK-kolbe for å kunne montere et AR buffer tube-sett. Denne adapteren er enkel å installere uten noen modifikasjoner på din AK. Det er ikke nødvendig å gjøre permanente endringer på kolbetangen, da den passer inne i adapteren og tuben. Dette produktet vil ta din AK inn i det tjueførste århundre med utseendet og justerbarheten til en M4. Strike Industries har også inkludert QD (quick disconnects) på begge sider av AK-kolbeadapteren.

799 NOK 1 kr 799,00 *

Leveringstid ca. 14-21 dager.
1 stk. på lageret i USA

Spesifikasjoner: Finish: Black Material: Aluminum

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Top takeaways

Strike Industries kolbeadapter lar deg erstatte en standard fast AK-kolbe med et AR buffer tube-sett uten modifikasjoner.
Adapteren er enkel å installere og krever ingen permanente endringer på kolbetangen.
Inkluderer QD (quick disconnects) på begge sider for økt funksjonalitet og justerbarhet.

Attributes

Finish: Black Material: Aluminum Leveringsvekt: 0,125kg Frakthøyde: 44mm Fraktbredde: 44mm Fraktlengde: 70mm

Elementdetaljer

US eksport klassifisering: 0A501.y.1

Oppgrader din AK med Strike Industries AK til AR buffer tube adapter! Enkel installasjon uten modifikasjoner. Få M4-utseende og justerbarhet. 🛠️ Lær mer nå!

SPECS: Length: 2.5", Weight: 4oz, Material: T6061 Aluminum.

Mer...

SPECS: Lengde: 2.5", Vekt: 4oz, Materiale: T6061 Aluminium.

Mer...

Kundevurderinger for STRIKE INDUSTRIES AK TO AR BUFFER TUBE ADAPTER BLACK ALUMINUM

Antall vurderinger: 5
Fra brownells.com: 5
Gjennomsnittsvurdering: 3,8

does not fit (29.05.2015)

Sturdy design, but does not even come close to fitting C39V2 rifle from century

Fits Great - FOR STAMPED AK's ONLY! (03.06.2015)

The review below me tried fitting it on a milled AK (C39v2). The Brownells video states it's for STAMPED AK's only. Fit well on my DDI stamped AK.

Worth getting to modify your AK (05.09.2015)

So far, so good (25.10.2015)

Exellent product, but... (16.02.2018)

Les 5 flere anmeldelser fra brownells.com

Logg inn

Glemt passord?
Registrere

CONNECT

NETTSTEDSKART

PRODUKTKATEGORIER

BESTILLING

KUNDE SERVICE

Velkommen!

Velkommen til Brownells.no, Norges ledende leverandør av våpenrelaterte produkter, våpendeler, børsemakerverktøy, ladeverktøy, ladeutstyr og ladekomponenter!

Vårt kundeløfte:

Uansett om du bare liker å skyte, har våpen som hobby, er børsemaker og reparerer våpen daglig eller bare eier et våpen er dette siden for deg! I over 75 år har skyttere, profesjonelle børsemakere, hobby utøvere, militæret, politiet og våpenreparatører kommet til Brownells for å finne produkter og deler av høy kvalitet. Hos oss finner du over 40 000 produkter inkludert unike våpendeler, tilbehør, børsemakerverktøy, ladeverktøy, ladeutstyr, komponenter, ammunisjon og andre produkter for å vedlikeholde, reparere eller oppgradere dine våpen.