Din handlekurv er tom.

Handlekurv

37 17 00 00

Meld på nyhetsbrev

Z-M WEAPONS
AR-15/M16 ACCU-WEDGE

993150100

Instantly Tightens Loose Upper & Lower Receivers

Helps promote better accuracy by making the upper and lower receiver fit tighter. Open upper receiver; drop this long-wearing, rubber wedge into the rear of the lower, behind the push pin. Absolutely no modifications required.

SPECS: High-density, thermo-plastic rubber, ½" (12.5mm) long.

Mer...

Gjør umiddelbart løse Upper & Lower Receivers strammere

Bidrar til å fremme bedre nøyaktighet ved å gjøre at upper og lower receiver passer strammere sammen. Åpne upper receiver; slipp denne slitesterke, gummi kilen inn i bakre del av lower, bak tappen. Absolutt ingen modifikasjoner nødvendig.

SPECS: Høy tetthet, termoplastisk gummi, ½" (12.5mm) lang.

Mer...

Kundevurderinger for Z-M WEAPONS ACCU-WEDGE

Antall vurderinger: 17
Fra brownells.com: 17
Gjennomsnittsvurdering: 4

Really tightens things up! (14.09.2009)

Makes upper and lower assemblies extremely snug fitting. Extra pressure is needed to close the take down pin. I wouldn't try "snapping" the upper group to facilitate mating the assemblies. The wedge would appear to decrease the rate of wear caused by pivot and take down pins jarring their receiver hole during extended shooting sessions. Trimming is NOT recommended.

No brainer-- get it!!! (31.10.2009)

Why are you wasting time reading this review? Just get it!!! It's about the only way you're going to tighten that upper down, and at [$], why argue? It works way better than the JP tensioner that costs 7 times more. If it doesn't tighten enough for your taste, all you have to do is put a spacer underneath it, and you're back in business.

DOES NOT WORK WITH RRA and S&W AR15 (19.12.2009)

It was questionable when I ordered the wedge if it would work with my Rock River Arms Elite Comp. I thought maybe it would fit in my Smith and Wesson M&P 15 but that's not the case as well. Don't order this brand of Accuwedge if you own one of the two ARs I mentioned.

Accu Wedge will not work on RRA ARs (06.02.2010)

I purchased an Accu Wedge to use on my RRA AR15 that has a slight play between upper and lower. When Accu Wedge is installed, it obstructs the closing of the upper and lower. I finally used a razor blade to trim bottom of wedge so it would fit. With almost 90% of base cut away, it finally allowed a tight fit but this wedge is not universal. It may work on other brands fine.

Accu-Wedge (22.05.2010)

I have been using an ACCU-Wedge in my COLT HBAR II competition carbine for twelve years. I have used in on military ranges, competition ranges and even in a hunting environment. It works perfectly in my Colt HBAR II and in government issue M-4/M-16s, can't comment on X brands as I have no experience with them. When the ACCU-Wedge was first offered, Colt pretty well owned the AR-15 market, so obviously, that's what it was designed for. I don't quite understand complaints where buyer's and users give lower ratings because they had to trim or make adjustments. By having to do so, you now can now easily (and best of all, cheaply) fall into the custom category, instead of the simpleton's world of plugging in something and expecting it to work perfectly. What a simple adjustment to have to make for an inexpensive improvement. By the way, the AR-15/M-16 series weapons are much like the M1911/A1 pistols. Gap and space are normal between upper and lower receivers and work perfectly well as designed. This $5.00 part can take that irritating (but harmless) play out without any harmful modification and makes a best-of-both worlds pleaser, that even an idiot without tools can install/de-install. I highly recommend it. I had one in my government issue M-4 while deployed to Iraq in 04-05 where it functioned flawlessly and with much use. When I returned home, I simply took it out and threw it away. Buy one, trim it if you must, use it, you'll love it.

Good product at a good price (23.09.2010)

I custom built my AR with a DS lower and generic upper I bought at a gun show, there was some standard play in between each so I tried out this product. It is easy to install, and solved the problem. I can see how some reciever combos might not work with this wedge, but all you need to do is razor blade some slack off, welcome to the world of gunsmithing.

accu wedge (04.01.2011)

the accu wedge dropped in to my DPMS perfect with no mods, nice and snug now no slop at all

IT DOES MAKE A DIF. (07.08.2011)

M-2- MIKE . IT DOES CHANGE THE SPOT UR SCOPES ON.PLAY BETWEEN UPPER AND LOWER. PUT A BORE SIGHT ON UR AR THEN MOVE THE PLAY SEE WHAT HAPPINS.THIS LITTLE BABY STOPS THAT CHANGE THAT CAN HAPPIN WITH TOO MUCH PLAY.LONG RANGE 1/8 CAN TURN INTO INCHES.IM GETTING 2 MORE.LOL

Installed in a Colt LE carbine (25.08.2011)

Fit perfect, installed in a new rifle but I have others that have loosened up and these always work! No trimming needed for me and it dropped rigfht in!

Perfect fit in my Bushmaster (24.01.2012)

My Bushmaster wasn't very loose to start with, but I figured for [$], why not try it. Dropped right in and fit perfect. Upper is now rock solid and rattle free.

Save your money (01.03.2012)

Wouldn't fit my DPMS without trimming. No difference in tightness between upper and lower.

Works Well As A Buffer.. (03.04.2014)

The polymer Accu-Wedge does not tighten receivers "rock solid" as some proclaim. The receivers will twist side to side according to pin fitment. What the Accu-Wedge does is act as a shock absorber or buffer. Without it the parts slam into each other and wear faster.
I've used many receiver combinations and the wedge has always fit although sometimes closing the receivers requires a good grip. Excess force should not be applied to the upper receiver overhang for the charge handle. The wedge will eventually settle in making closing the receivers easier.
The Accu-Wedge is recommended however I use other means to tighten receivers "rock solid."

Lots of trimming for Rock River lower (15.08.2014)

So this will require a lot of trimming in order to fit a RR lower. I shaved the bottom plug by 75% of its original height, I also had to chop the lip a little as well. Now that's not too big a deal because the play between my Yankee Hill upper and the lower is 99% gone, 100% no rattle. Just be sure to use a nice, small box cutter.. I used my Cold Steel XL Espada.. that was tricky.

Not for M&P 15 (08.02.2017)

Not enough room under or in back of the TDP on a S&W M&P 15. Trimming this thing was a chore, like trying to hold a piece of jello and tough to get a smooth cut. Had the base down to about 1/8" thick and about 1/8" off the wedge and still couldn't get the rifle closed enough to pin it. While I might recommend this to someone based on its good concept, it just doesn't work with this particular model AR.

Works great (28.07.2017)

My Colt SBR lower had a lot of slop in it. To much.....

I purchased one of these, trimmed it to fit and not it doesn't rattle anymore.

P.S. Slop between lower and upper has nothing to do with accuracy. Only shooter confidence.

For me it was annoying to have that much slop.

I WAS annoying.

It took the wibble out of my wobble (26.11.2017)

I just bought a new AR15 and the upper to lower fit was not satisfactory. However because it did not pose a safety problem I looked to Brownell's for the fix and found it when a friend recommended the AccuWedge. I installed it and found it needed a bit of trimming to allow the halves to fit. Dremel to the rescue. 1 minute's work and the wedge fit perfectly. No more wobble and loose fit. Thanks Brownell's.

Get a razorblade ready (02.02.2018)

First, understand that Browne!ls is great with which to do business; I use them a lot. But not all products they sell have that stellar reputation.

I installed the wedge on a S&W M&P 15 TS, and maybe tolerances are tighter. But I ended up cutting away about 60% of it before I could get the pin to lock the upper. Instructions say "squeeze" the upper down to lock. More like use a vise, which I certainly wasn't going to do. So I went to whittling.

Does it stop wobble? Yes.

Is it worth the price? Maybe not, especially if you have to whittle it down to almost nothing.

Got a loose fit on your AR? Might help.

Will I buy another? Probably not. For many years I didn't use one, and never missed it.

If the round base were MUCH thinner it would probably be a drop in.

Maybe buy a couple of school erasers for 50 cents and make your own.

I give it 3 stars.

Les 17 flere anmeldelser fra brownells.com

199 199 1 NOK

Produktnr.: 993150100
Z-M WEAPONS ACCU-WEDGE
Produsentnr.: AW400 Bidrar til å fremme bedre nøyaktighet ved å gjøre at upper og lower receiver passer strammere sammen. Åpne upper receiver; slipp denne slitesterke, gummi kilen inn i bakre del av lower, bak tappen. Absolutt ingen modifikasjoner nødvendig.

199 NOK 1 162 kr 199,00 *

Leveringstid ca. 14-21 dager.
Mer enn 10 stk. på lager i USA

Spesifikasjoner: Make: AR-15

Legg til ønskeliste

Still spørsmål

Detaljer

Legg til ønskeliste

Still spørsmål

Attributes

Make: AR-15 Leveringsvekt: 0,005kg Fraktbredde: 57mm Fraktlengde: 89mm

Elementdetaljer

Made in USA

Forbedre nøyaktigheten på din AR-15 med Z-M WEAPONS ACCU-WEDGE. Enkel installasjon uten modifikasjoner. Gjør upper og lower receiver strammere sammen. 🚀🔧 Lær mer!

Instantly Tightens Loose Upper & Lower Receivers

SPECS: High-density, thermo-plastic rubber, ½" (12.5mm) long.

Mer...

Gjør umiddelbart løse Upper & Lower Receivers strammere

SPECS: Høy tetthet, termoplastisk gummi, ½" (12.5mm) lang.

Mer...

Kundevurderinger for Z-M WEAPONS ACCU-WEDGE

Antall vurderinger: 17
Fra brownells.com: 17
Gjennomsnittsvurdering: 4

Really tightens things up! (14.09.2009)

No brainer-- get it!!! (31.10.2009)

DOES NOT WORK WITH RRA and S&W AR15 (19.12.2009)

Accu Wedge will not work on RRA ARs (06.02.2010)

Accu-Wedge (22.05.2010)

Good product at a good price (23.09.2010)

accu wedge (04.01.2011)

the accu wedge dropped in to my DPMS perfect with no mods, nice and snug now no slop at all

IT DOES MAKE A DIF. (07.08.2011)

Installed in a Colt LE carbine (25.08.2011)

Fit perfect, installed in a new rifle but I have others that have loosened up and these always work! No trimming needed for me and it dropped rigfht in!

Perfect fit in my Bushmaster (24.01.2012)

My Bushmaster wasn't very loose to start with, but I figured for [$], why not try it. Dropped right in and fit perfect. Upper is now rock solid and rattle free.

Save your money (01.03.2012)

Wouldn't fit my DPMS without trimming. No difference in tightness between upper and lower.

Works Well As A Buffer.. (03.04.2014)

Lots of trimming for Rock River lower (15.08.2014)

Not for M&P 15 (08.02.2017)

Works great (28.07.2017)

It took the wibble out of my wobble (26.11.2017)

Get a razorblade ready (02.02.2018)

Les 17 flere anmeldelser fra brownells.com

Kunder kjøpte også
Alternativer

BROWNELLS AR-15/M16 ACTION BLOCK & LOWER VISE BLOCK SET
AR-15/M16 LOWER RECEIVER VISE BLOCK

BROWNELLS

På lager

kr 899,00 * kr 399,00 - kr 899,00*

Bench & Vise Blocks

3,6

Sale

MAGPUL AR-15/M16 ENHANCED TRIGGERGUARD
AR-15/M16 ENHANCED TRIGGERGUARD

MAGPUL

På lager

kr 373,10 *

Veil. pris kr 439,00

Avtrekkerbøyler

4,3

Sale

MAGPUL B.A.D. LEVER
AR-15/M16 B.A.D. LEVER™

MAGPUL

På lager

kr 551,70 *

Veil. pris kr 649,00

SINCLAIR INTERNATIONAL CHAMBER FLAG-3 PACK
AR-15 CHAMBER SAFETY FLAG

SINCLAIR INTERNATIONAL

På lager

kr 179,00 * kr 119,00 - kr 179,00*

Kammer sikkerhetsflagg

ROCK RIVER ARMS M4 STOCK WRENCH
AR-15 M4 STOCK WRENCH

ROCK RIVER ARMS

Kommer til lager

kr 199,00 *

Skiftenøkler

3,7

BROWNELLS ACCU-WEDGE
AR-15/M16 ACCU-WEDGE

BROWNELLS

Kommer til lager

kr 149,00 *

Accu-Wedges

COLT ACCU-WEDGE
ACCU-WEDGE

COLT

På lager

kr 279,00 *

Accu-Wedges

Logg inn

Glemt passord?
Registrere

CONNECT

NETTSTEDSKART

PRODUKTKATEGORIER

BESTILLING

KUNDE SERVICE

Velkommen!

Velkommen til Brownells.no, Norges ledende leverandør av våpenrelaterte produkter, våpendeler, børsemakerverktøy, ladeverktøy, ladeutstyr og ladekomponenter!

Vårt kundeløfte:

Uansett om du bare liker å skyte, har våpen som hobby, er børsemaker og reparerer våpen daglig eller bare eier et våpen er dette siden for deg! I over 75 år har skyttere, profesjonelle børsemakere, hobby utøvere, militæret, politiet og våpenreparatører kommet til Brownells for å finne produkter og deler av høy kvalitet. Hos oss finner du over 40 000 produkter inkludert unike våpendeler, tilbehør, børsemakerverktøy, ladeverktøy, ladeutstyr, komponenter, ammunisjon og andre produkter for å vedlikeholde, reparere eller oppgradere dine våpen.