Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge

fri frakt juli

BROWNELLS CROWN SAVER™ LATHE CENTER COVER


Large Crown Saver, 3-pak

Auto-oversatt beskrivelse (Beskrivelse - Produsent): Disse messing kjegler ta mye av angst av dreiebenk-snu et perfekt god fat med en allerede ferdig krone. Sett en krone sparer fra snuten og dreiebenk eller møllen midten før fluting, chambering, polering eller tråder for en snute brems, og kan du være trygg du ikke skade rifling eller ding kronen. Mer...

Produktnr.: 080000869 080000869
Your Safeguard When Turning Barrels With Finished Crowns
These brass cones take much of the anxiety out of lathe-turning a perfectly good barrel with an already finished crown. Insert a Crown Saver between the muzzle and lathe or mill center before fluting, chambering, polishing, or threading for a muzzle brake, and you can rest assured you won’t harm the rifling or ding the crown. Each brass cone is machined to within .0002" or less concentricity, making using a Crown Saver as accurate as direct barrel contact against the center. With a Crown Saver, you virtually eliminate any chance of swaging the rifling. It stays seated and will not spin in the bore when the barrel is chucked in the lathe. Small fits bores .17 to .45 caliber. Large fits bores up to .50 caliber. For best results, do not use Crown Saver more than once on barrels of the same caliber.

SPECS: 360 brass. Maximum diameter. Small - .500", Large - .750".

BROWNELLS
258 404 2 NOK
080000869
Large Crown Saver, 3-pak Disse messing kjegler ta mye av angst av dreiebenk-snu et perfekt god fat med en allerede ferdig krone. Sett en krone sparer fra snuten og dreiebenk eller møllen midten før fluting, chambering, polering eller tråder for en snute brems, og kan du være trygg du ikke skade rifling eller ding kronen. Hver messing kjegle er maskinert til innenfor. 0002" eller mindre konsentrisitet, gjør benytter en krone sparer så nøyaktig som direkte fat kontakt mot midten. Med en krone Saver eliminere du nesten enhver mulighet for swaging rifling. Det blir sittende og vil ikke spinne i bar når tønnen er kastet i i dreiebenk. Liten passer kjeder.17 til.45 kaliber. Stor passer kjeder til.50 kaliber. For best resultat, ikke bruk Crown sparer mer enn én gang på fat av samme kaliber.
258 NOK 11 kr 258,00 *

10+ på lager

Elementdetaljer

Made in USA




080000379
Small Crown Saver, 10-pak
Produsentnr.: 080000379 Liten Crown Saver, 10-pak
404 NOK 33 kr 404,00 *

10+ på lager
Your Safeguard When Turning Barrels With Finished Crowns
These brass cones take much of the anxiety out of lathe-turning a perfectly good barrel with an already finished crown. Insert a Crown Saver between the muzzle and lathe or mill center before fluting, chambering, polishing, or threading for a muzzle brake, and you can rest assured you won’t harm the rifling or ding the crown. Each brass cone is machined to within .0002" or less concentricity, making using a Crown Saver as accurate as direct barrel contact against the center. With a Crown Saver, you virtually eliminate any chance of swaging the rifling. It stays seated and will not spin in the bore when the barrel is chucked in the lathe. Small fits bores .17 to .45 caliber. Large fits bores up to .50 caliber. For best results, do not use Crown Saver more than once on barrels of the same caliber.

SPECS: 360 brass. Maximum diameter. Small - .500", Large - .750".