Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Norge

EGW
1911 PRACTICAL BALLESTER MOLINA EXTRACTOR

841370116058 296000517
Will not work with Schwartz style safety. The steel available today is of much higher quality than what was available in 1911 when the 1911 pistol was first produced. Improvements to the entire manufacturing process include better alloys, more controlled furnaces, vacuum heat treat, better tooling, and finite element analysis-all of which EGW uses in production. EGW-specific Improvements to the original Ballester Extractor: EGW found that the extractor rides up the relief groove on the ammunition casing with each round fired: this dulls the hook from constantly banging the case, over time tension is lost, leading to a jammed case which adversely affects accuracy. EGW has fixed all 3 of these problems by reducing the distance from the bolt face to the extractor hook. They found that most hook designs are cut straight at a right angle. They machined theirs at an acute angle so that there is more surface area for the hook to bite into the case. Right angles are a weak point on other extractors so they put radii on both sides of theirs to increase strength. The hook is machined with a special cutter that leaves a nice clean radius in the inside corner where most extractors fail. Lastly their extractor is vacuum heat treated yielding great spring properties and the capability to maintain tension for 70,000+ rounds.
899 899 1 NOK
Produktnr.: 296000517
EGW 1911 PRACTICAL BALLESTER MOLINA EXTRACTOR
Produsentnr.: 10355 841370116058 Vil ikke fungere med Schwartz-stil sikkerhet. Stålet som er tilgjengelig i dag er av mye høyere kvalitet enn det som var tilgjengelig i 1911 da 1911-pistolen først ble produsert. Forbedringer i hele produksjonsprosessen inkluderer bedre legeringer, mer kontrollerte ovner, vakuumvarmebehandling, bedre verktøy og finit elementanalyse - alt dette bruker EGW i produksjonen. EGW-spesifikke forbedringer til den originale Ballester Extractor: EGW fant ut at extractoren glir opp i lettelsessporet på ammunisjonskassen for hvert avfyrt skudd: dette sløver kroken ved konstant å banke mot hylsen, over tid går spenningen tapt, noe som fører til en fastklemt hylse som negativt påvirker nøyaktigheten. EGW har løst alle disse tre problemene ved å redusere avstanden fra sluttstykkets ansikt til extractor-kroken. De fant ut at de fleste krokdesign er kuttet rett i en rett vinkel. De maskinerte sin i en akutt vinkel slik at det er mer overflateareal for kroken å bite seg fast i hylsen. Rette vinkler er et svakt punkt på andre extractor, så de la radiuser på begge sider av deres for å øke styrken. Kroken er maskinert med en spesiell kutter som etterlater en fin ren radius i det indre hjørnet hvor de fleste extractor feiler. Til slutt er deres extractor vakuumvarmebehandlet, noe som gir flotte fjæregenskaper og evnen til å opprettholde spenning for 70 000+ runder.
899 NOK 3 kr 899,00 *
Leveringstid ca. 14-21 dager.
3 stk. på lageret i USA
Spesifikasjoner: Finish: Blue Make: 1911

Attributes

Finish: Blue Make: 1911 Leveringsvekt: 0,01kg Fraktbredde: 102mm Fraktlengde: 152mm

Elementdetaljer

Made in USA
US eksport klassifisering: 0A501.x



Will not work with Schwartz style safety. The steel available today is of much higher quality than what was available in 1911 when the 1911 pistol was first produced. Improvements to the entire manufacturing process include better alloys, more controlled furnaces, vacuum heat treat, better tooling, and finite element analysis-all of which EGW uses in production. EGW-specific Improvements to the original Ballester Extractor: EGW found that the extractor rides up the relief groove on the ammunition casing with each round fired: this dulls the hook from constantly banging the case, over time tension is lost, leading to a jammed case which adversely affects accuracy. EGW has fixed all 3 of these problems by reducing the distance from the bolt face to the extractor hook. They found that most hook designs are cut straight at a right angle. They machined theirs at an acute angle so that there is more surface area for the hook to bite into the case. Right angles are a weak point on other extractors so they put radii on both sides of theirs to increase strength. The hook is machined with a special cutter that leaves a nice clean radius in the inside corner where most extractors fail. Lastly their extractor is vacuum heat treated yielding great spring properties and the capability to maintain tension for 70,000+ rounds.
Nyhetsbrev